| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What is the routing metric used by RIP?
A.) Route poisoning
B.) Split horizon
C.) Hop Count
D.) TTL | | 1 |
| Which layer hides details of network dependent information from
the higher layers by providing transparent data transfer?
A.) Transport
B.) Physical
C.) Data Link
D.) Session
E.) Application
F.) Network | | 1 |
| Identify 3 characteristics of a MAC address?
A.) Burned into the NIC
B.) 48 bits long
C.) Length is 32 bits
D.) Used to deliver the frame to the end device
E.) Contains a network portion and a host portion | | 1 |
| Identify the hardware component that stores the bootstrap
program?
A.) ROM
B.) NVRAM
C.) Booter load
D.) RAM
E.) Flash | | 2 |
| Windowing is a type of?
A.) Negative acknowledgement
B.) Address resolution
C.) Layer transition mechanism
D.) Flow control | | 1 |
| Which three types of connectors are commonly associated
with Cisco's V.35 serial cables? (Choose three.)
0 RJ 11
1 DB 60
2 Winchester 15 pin
3 DB 9
4 smart serial
5 RJ 45
| | 3 |
| Which three are typical operational phases in a basic
connection oriented network service?
A. call setup
B. data transfer
C. load balancing
D. call termination
E. caller ID
F. call prionflication
G. data segmentation
H. data and momma
I. data link identification
J. callering book | | 1 |
| what is the difference between client mode and server mode of
vtp and what is the diffrence betwwen tarnsparent mode and
server mode | IBM | 4 |
| What is the default size of a standard ping on a Cisco router?
* A: 100 bytes
* B: 32 bytes
* C: 10 bytes
* D: 16 bytes
| CMS | 2 |
| Which of the following are Presentation Layer standards?
A.) JPEG and PICT
B.) MPEG and MIDI
C.) ASCII and EBCDIC
D.) NFS and SQL | | 2 |
| Which two does 100BaseT use?
A.) CSMA/CD
B.) IEEE 802.5
C.) 802.3u
D.) Switching with 53-byte cells | | 3 |
| What are four ways that Fast Ethernet compares to 10BaseT
Ethernet? (Choose four)
A. Fast Ethernet uses the same Maximum Transmission Unit (MTU)
B. Fast Ethernet is based on an extension to the IEEE 802.3
specification
C. Fast Ethernet uses the same Media Access Control (MAC)
mechanisms
D. Fast Ethernet preserves the frame format that is used by
10BaseT Ethernet
E. Fast Ethernet errors a speed increase one hundred times
that of the 10BaseT Ethernet | | 1 |
| Hello Mr.Jitendera Kuamr Sinha, how is every thing going
on? Thanks for your reply. Dear Friend if you can Explain
it little bit deeper i will be realy thanks full. Wish you
all the Best.
| | 1 |
| Which command would you type to show SAP and RIP updates you are
receiving on an interface?
A.) sh ipx servers
B.) sh ipx traffic
C.) sh ipx interface
D.) sh ipx route | | 1 |
| Extended IP access-lists (100-199) can be used to control
traffic.
Which command listed below will permit smtp mail to only
host 3.4.5.6 ?
A.) It is not possible for SMTP traffic
B.) access-list 102 permit tcp any host 3.4.5.6 eq smtp
C.) access-list 101 permit tcp any 3.4.5.6 0.0.0.0 eq 23
D.) access-list 102 permit tcp any any eq smtp
E.) access-list 101 permit tcp any 3.4.5.6 0.0.0.0 eq 25 | | 1 |
| With distance vector routing protocols, it is never useful
to send
the same routing update packet back out the same interface
that it was
learned. This concept is called what?
A.) Holddown timers
B.) Poison Reverse
C.) Count to infinity
D.) Split Horizon
E.) Link State | | 2 |
| What 2 commands verify end to end communications?
A.) Trace
B.) debug ip session
C.) Ping
D.) Route | | 2 |
| We know that TCP provides connection oriented services, what
else
does it provide?
A.) FECN & BECN
B.) Path discovery.
C.) Flow control and error checking.
D.) Name resolution.
E.) File manipulation. | | 1 |
| Which of the follwing are true of standard half-duplex
Ethernet circuitry?
A. It is alternate one-way communication
B. The receive (RX) is wired directly to the transmit (TX)
of the remote station
C. The transmit (TX) is wired directly to the receive (RX)
of the remote station
D. Collisions are not possible
E. Both stations can transmit simultaneously | | 1 |
| The following commands were entered at the command prompt of a
Cisco router. What do they accomplish?
access-list 1000 deny 9e.1234.5678.1212 4
access-list 1000 permit -1
interface ethernet 0
ipx network 9e
interface ethernet 1
ipx network 4a
interface serial 0
ipx network 1
ipx output-sap-filter 1000
A. File server advertisements from server 9e.1234.5678.1212
will not be
forwarded on interface S0.
B. All other SAP services, other than file server, from any
source will
be forwarded on S0.
C. All other SAP services, other than print server, from any
source will
be forwarded on S0.
D. Print server advertisements from server 9e.1234.5678.1212
will not be
forwarded on interface S0. | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
