| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the true statements about the following access list:
Access-list 101 deny tcp 192.10.172.0 0.0.0.255 any eq 23
Access-list 101 permit ip any any
A.) This access list prevents the host 192.10.172.0 from
telneting
B.) This access list prevents any telnet traffic from subnet
192.10.172.0/24
C.) This access list filters some telnet access
D.) This access list denies any telnet traffic to subnet
192.10.172.0/24
E.) This access list is invalid
F.) The netmask on the this access list is reversed | | 1 |
| Regarding frame relay, which of the following statements are
true?
A.) You must use ANSI encapsulation if connecting to
non-Cisco equipment
B.) You must use IETF encapsulation if connecting to
non-Cisco equipment
C.) You must use Q.933a encapsulation if connecting to
non-Cisco equipment
D.) You must use Cisco encapsulation if connecting to
non-Cisco equipment | | 2 |
| Which three are typical operational phases in a basic
connection oriented neloyord service? (Choose three)
A. call setup
B. data transfer
C. load balancing
D. call termination
E. call priortization
F. data segmentation
G. data link identification | | 1 |
| Which of the following is true?
A. The default is to send debug output to the console screen.
B. To view debug output from a telnet session, the "terminal
monitor" command must be used
C. If the "logging buffered" command is used, the debug
output would be sent to RAM and can be viewed with the "show
log" command
D. If the "no console loggin" command were configured,
output would besent to a telnet session
E. All of the above
F. None of the above
G. A, B, and C.
H. A, C, D, and E. | | 2 |
| Given the IPX address 4a.0002.1111.a999, what is the network ID
and what is the node ID?
A.) net 4a host 0002.1111.a999
B.) net a999 node 0002.1111
C.) net 0002.1111.a999 node 4a
D.) net 0002.1111 node a999 | | 1 |
| Identify command that configures 'Cisco1' as a secret password?
A.) Router(config)# enable secret password Cisco1
B.) Router(config)# enable secret cisco1
C.) Router(config)# enable password Cisco1
D.) Router(config)# enable secret Cisco1 | | 2 |
| What are characteristics of UDP
A. It is reliable and acknowledged
B. It is unreliable and acknowledged
C. It is reliable and unacknowledged
D. It is unreliable and unacknowledged | | 2 |
| Which layer is responsible for determining if sufficient
resources
for the
intended communication exists?
A.) Application
B.) Network
C.) Session
D.) Presentation
E.) Transport | | 2 |
| Identify the administrative distance and appropriate routing
protocol?
A.) RIP = 255, IGRP = 100
B.) RIP = 100, IGRP = 120
C.) RIP = 1, IGRP = 0
D.) RIP = 120, IGRP = 100 | | 3 |
| IPX traffic using different encapsulation types can go over
the same data link
A. True
B. False | | 1 |
| Which service uses telephone control messages and signals
between
the transfer points along the way to the called destination?
A. Signaling System 7 (SS7)
B. Time-division Multiplexing (TDM)
C. X.25
D. Frame relay | | 1 |
| Identify the definition of demarcation?
A.) Date in which the WAN service contract expires
B.) Cabling which extends from the WAN service provider to
the customer
C.) Division of responsibility, where the CPE ends and the
local loop
begins
D.) Equipment which is located at the customer premises | | 1 |
| Which two physical interfaces support PPP? (Choose two)
A. Ethernet
B. Token Ring
C. Synchronous serial
D. Asynchronous serial | | 1 |
| Which protocol is used for booting diskless workstations?
A.) IP
B.) ARP
C.) RARP
D.) TCP
E.) SNMP | | 1 |
| In regards to TCP/IP, which class of address allows for the
fewest
valid
Internet hosts?
A.) D
B.) E
C.) Classes are not used in TCP/IP.
D.) B
E.) C
F.) A | | 1 |
| What are the two primary operating modes for frame switching?
A. Full Duplex
B. Half-Duplex
C. CSMA/CD
D. Cut-through
E. Fragmentation
F. Store and Forward
G. User mode
H. Privileged mode | | 1 |
| When would you use ISDN?
A.) To connect LANs using POTS
B.) To support applications requiring voice, data, and video
C.) When you need a consistent and very high rate of data speed
D.) To connect to IBM mainframes | | 1 |
| What command would you use to find out the names of Novell
servers on a network?
A. show ipx servers
B. show ipx hosts
C. show ipx sap
D. show ipx nodes. | | 1 |
| Which statement is true regarding half duplex?
A.) Only works in a point-to-point configuration
B.) Allows for transmitting and receiving but not a the same
time
C.) Allow for transmitting and receiving of data simultaneously
D.) Doubles the bandwidth | | 1 |
| Identify 3 characteristics regarding CDP?
A.) On by default
B.) Shows only directly connected neighbors
C.) Requires IP or IPX
D.) 60 second update interval by default
E.) 30 second updates interval by default | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
