| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which command will give the following output:
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
* 0 CTY - - - - - 0 0 0/0 -
1 AUX 9600/9600 - - - - - 0 0 0/0 -
* 2 VTY - - - - - 2 0 0/0 -
3 VTY - - - - - 0 0 0/0 -
4 VTY - - - - - 0 0 0/0 -
5 VTY - - - - - 0 0 0/0 -
6 VTY - - - - - 0 0 0/0 - | | 1 |
| Identify the hardware component that stores the backup
configuration?
A.) RAM
B.) NVRAM
C.) Flash
D.) ROM | | 1 |
| When a Distance Vector routing protocol detects that a connected
network has gone down, it sends out a special routing update
packet,
telling all directly connected routers that the distance to
the dead
network is infinity. This is an example of which routing
technology?
A.) ICMP.
B.) Only Link State routing protocols have this intelligence.
C.) Triggered updates.
D.) Garrison-4.
E.) Split Horizon.
F.) Poison Reverse. | | 1 |
| You are logged into a router, what command would
show you the IP addresses of routers connected to you?
A. show cdp neighbors detail
B. show run
C. show neighbors
D. show cdp | | 2 |
| Which is true regarding half duplex Ethernet operation?
A.) Half Duplex ethernet technology provides a transmit
circuit connection
wired directly to the receiver circuit at the other end
B.) Half duplex transmission between stations is achieved by
using point
to multipoint Ethernet and Fast Ethernet
C.) With Half Duplex transmission logically circuits feed
into a single
cable creating a situation similar to a one way bridge
D.) Half Duplex transmission between stations is achieved
using Point to
Point Ethernet & Fast Ethernet | | 1 |
| What key do you use to view the last command?
A.) Left Arrow
B.) Ctrl-P
C.) Up Arrow
D.) Right Arrow | | 2 |
| What is the UDP datagram format?
A. Source Port - 16 bits, Destination Port - 16 bits, Length
- 16 Bits, Checksum - 16 bits, Data
B. Destination Port - 16 bits, Source Port - 16 bits, Length
- 16 Bits, Checksum - 16 bits, Data
C. Source Port - 16 bits, Destination Port - 16 bits,
Checksum - 16 Bits, Length - 16 bits, Data
D. Source Port - 8 bits, Destination Port - 8 bits, Length -8
Bits, Checksum - 8 bits, Data | | 1 |
| Which Cisco IOS command should you use to display the Novell
IPX address assignments on a router?
A. show ipx addresses
B. show ipx interface
C. show me the money
D. ipx, network (number)
E. display ipx addresses
F. show ipx routing details | | 1 |
| Identify the 3 methods routers learn paths to destinations?
A.) Dynamic routing
B.) None of the above, configured by default
C.) Default routes
D.) Administrative distance
E.) Static routes | | 1 |
| Identify the default values that make up IGRP's composite
metric?
A.) Bandwidth
B.) Load
C.) Reliability
D.) MTU
E.) Delay | | 1 |
| Identify the 3 major functions at layer 3 of the OSI model?
A.) Forwarding process
B.) Logical addressing
C.) End-to-end connections
D.) Path selection
E.) MAC address examination
F.) Network monitoring | | 1 |
| Identify the type of hardware required to connect a Token ring
network to
an Ethernet network?
A.) Repeater
B.) TR-Enet
C.) Router
D.) Token Ring to Ethernet translation hub | | 1 |
| Which can be logged by IPX extended access lists?
A.) source address
B.) protocol
C.) source socket
D.) access list number
E.) destination socket
F.) destination address | | 1 |
| In transport layer, for connection oriented communication
Three way handshake process is there to establish a
connection. So question is that, when a host send an ACK
messages to another host with host intend to establish a
connection, the source host send it as Broadcast or unicast
message? Cud anyone explain this.
Thanks in advance. | HCL | 3 |
| Which two of the following protocols are used at the
Transport layer?
A.) ARP
B.) UDP
C.) ICMP
D.) RARP
E.) TCP
F.) BootP | | 1 |
| Identify the command to configure the IP address 172.16.100.5
255.255.255.0?
A.) Router(config-if)# ip address 172.16.100.5 255.255.255.0
B.) Router(config)# ip address 172.16.100.5
C.) Router# ip address 172.16.100.5 255.255.255.0
D.) Router(config)# ip address 172.16.100.5 255.255.255.0 | | 2 |
| (1)what is "rtp" and how it work,
(2)what is diffrence between igrp and eigrp
(3)the slection prcedure of dr and bdr is depend open
(4)why frame really is called nbma
(5)what is ppp
(6) what is diffrence b/w tcp and udp
(7) how can we implement ospf protocall on any router
(8)whta is as nomber
(9)what is AD value
(10)what is the broadcast id,n/w id and number of vallid
host of the 255.255.255.128/25 195.168.10.10/25
(11) what is stub network
(12) what is contigues n/w
(13)on which type of router we can implement default routing
(14)what is diffrence b/w hub switch;switch router,
(15)what is v lan
(16)what is the diffrence b/w link sate protocal and
distance vector protocall
(17)what is synchoransh mode of data transfer and
asynchronash mode of data transfer
(18) question on lab,
belive me frnds there are 20 questions and 5 questions on
lab implimentaion.around 1.1/2 hour i was in interview room
and after givieng 17 right answera and 4 in lab i got
slected
try to give answer
if any difficulty or any prob plz email me on
jitenderasinha.it@gmail.com
if any one of you havae boson netsim plz also intimate me
| | 4 |
| When you cords an IP address on a place router which command
stale the IP processing on the interface?
A. ip enable
B. network ip-address
C. ip address ip-address subnet mask
D. the exit command from the enabled configuration
E. copy running-configuration to startup-configuration | | 3 |
| IPX traffic using different encapsulation types can go over
the same data link
A. true
B. false | | 1 |
| My question is how windows pc will act as a router?
Jitendra understand this question? I again want to ask you
is it possibele for windows pc to act like a router | | 2 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
