ALLInterview.com :: Home Page            
 Advertise your Business Here     
Browse  |   Placement Papers  |   Company  |   Code Snippets  |   Certifications  |   Visa Questions
Post Question  |   Post Answer  |   My Panel  |   Search  |   Articles  |   Topics  |   ERRORS new
   Refer this Site  Refer This Site to Your Friends  Site Map  Bookmark this Site  Set it as your HomePage  Contact Us     Login  |  Sign Up                      
Google
   
 
Categories >> Engineering >> Electrical Engineering
 
 


 

 
 Civil Engineering interview questions  Civil Engineering Interview Questions (3070)
 Mechanical Engineering interview questions  Mechanical Engineering Interview Questions (3287)
 Electrical Engineering interview questions  Electrical Engineering Interview Questions (13321)
 Electronics Communications interview questions  Electronics Communications Interview Questions (2362)
 Chemical Engineering interview questions  Chemical Engineering Interview Questions (416)
 Aeronautical Engineering interview questions  Aeronautical Engineering Interview Questions (77)
 Bio Engineering interview questions  Bio Engineering Interview Questions (17)
 Metallurgy interview questions  Metallurgy Interview Questions (79)
 Industrial Engineering interview questions  Industrial Engineering Interview Questions (163)
 Instrumentation interview questions  Instrumentation Interview Questions (2374)
 Automobile Engineering interview questions  Automobile Engineering Interview Questions (106)
 Mechatronics Engineering interview questions  Mechatronics Engineering Interview Questions (38)
 Marine Engineering interview questions  Marine Engineering Interview Questions (43)
 Power Plant Engineering interview questions  Power Plant Engineering Interview Questions (75)
 Engineering AllOther interview questions  Engineering AllOther Interview Questions (1195)
Question
Do you know how to joint the H.T and L.T Cables?
 Question Submitted By :: Electrical-Engineering
I also faced this Question!!     Answer Posted By  
 
Answer
# 1
hello dear,jointing the cable not by using transformer or
by fevicol,and its not a simple like paper r wood jointing
by fevicol..
by using the heat strinkable method cable jointing will be
done,the heat strinking method gives high insulation to the
cable at jointing end,it can be used for jointing ht panel
board at the termination end,the kit used for the heat
strinkable is heavely insulation material,the joint will be
done by heating material...
for jointing the LT to LT cable above 6
sqmm,10,16,35,50,70,90,120,150,185,240,300,400,sqmm cable
by jointing the FERRULE LUG between the cable joint by
using cripping tools and then insulation tape will be
rounded it heavely......
 
Is This Answer Correct ?    95 Yes 16 No
Vinothbhabu
 
Answer
# 2
heat shrink joint is the best method. please check with
Rechem website.

No there is a new tehnology update that is Cold shrink
joint.
 
Is This Answer Correct ?    32 Yes 5 No
Rvg.msceb
 
 
 
Answer
# 3
The question is itself creating confusion. Are you asking
about the connection/jointing method,
or are you askinmg about the connection between HT-LT voltage?
 
Is This Answer Correct ?    12 Yes 0 No
Jyotirmaya Patra
 
Answer
# 4
HT line tuns into LT by step down txr then connected lt
with LT cable
 
Is This Answer Correct ?    19 Yes 11 No
Sanjeet Swarnakar
 
Answer
# 5
h.t. cables are joint by using h.v. straight througk joint
if it is cable and then heat shrink by using the
insulation .
l.t. cables are joint by using l.v. lugs and covered with
insulation and heat shrink or may be taken to H pole
structure to join with thimbles.
 
Is This Answer Correct ?    11 Yes 5 No
Pravesh
 
Answer
# 6
to joint these cableslike L.T. & H.T. cables there are many
componyes are providing the jointing kit for low tansion
cable in that kit some insulating material,lugs,earthing
wire, past to fill in joint are avable and instrction
manual also avable with kit. so we must read the jointing
procidure in the instruction manual & use this material to
joint the cable.
 
Is This Answer Correct ?    6 Yes 2 No
Rajendra
 
Answer
# 7
H.T cable joint can be done by two method.
By Heat shrink kit or by m seal kit.If cable is unearth
prefere to use heat shrink kit. in earth cable prefere to
use m seal kit.
Two L.T Cable joint done by m seal kit(low voltage kit)
and end termination done by bimatalic lugs.
 
Is This Answer Correct ?    21 Yes 18 No
Dilip B Shah
 
Answer
# 8
you should not join h.t. & l.t. cables because both are used
for the different current rating & voltage rating.

if you are asking about connection then
1. for step up & step down the voltage you can connect to
the transformer.

2. for distribution you can connect to breaker.

or

if you are asking about jointing then it is not good but

1. you can joint by jointing kit. ( heat srinkeble ) as you
asked your cable is h.t & l.t it 3-core & more than 25
SQ.MM SO There is no other way to joint it.
 
Is This Answer Correct ?    6 Yes 3 No
Mehul G. C.
 
Answer
# 9
i agree with gobi but with little addition vinothbhabu
in ht cable jonting one more jont is their that is compound
joint thid is also good method for ht cables
 
Is This Answer Correct ?    0 Yes 0 No
Surya
 
Answer
# 10
for cable joining splicing method is used i.e otdr equipement is used 
Is This Answer Correct ?    0 Yes 0 No
Sarvesham Nayar
 

 
 
 
Other Electrical Engineering Interview Questions
 
  Question Asked @ Answers
 
what is different between installation and commonissonig.   3
What are pre paid energy meters ? How it works ? Siemens 1
Is there any local or International standards that prohibit the installation of earthing pit in the planters area where the earthing pit is subject to continues soak in water?   1
what s d difference between inverter an ups Jindal 1
WHY ARE THE LT GENERATORS SOLIDLY EARTHED WHILE THE HT GENERATORS ARE EARTHE THROUGH NGR OR NGT??   3
what is the function of starter & choke in the tube light set & how choke give 1000 volts while switching on. IBM 11
Why machines are avoided to work is saturation region of B- H curve?   3
what is the difference between earth and neutral. DLF 8
in three phase with neutral connection, what will happen,if the neutral is in open condition with single phase distribution panel   4
why return path in terms of neutral is required please give a relevant answer   3
What is the starting current of a DC Motor?   2
what is differance between PT-100 and thermocouple?   1
 
For more Electrical Engineering Interview Questions Click Here 
 
 
 
 
 


   
Copyright Policy  |  Terms of Service  |  Articles  |  Site Map  |  RSS Site Map  |  Contact Us
   
Copyright 2013  ALLInterview.com.  All Rights Reserved.

ALLInterview.com   ::  KalAajKal.com