Lube oil pressure transmitter local it's showing 9.8 kg/cm2 but dcs side it's showing 9.26 like that what is the reason?

Answers were Sorted based on User's Feedback



Lube oil pressure transmitter local it's showing 9.8 kg/cm2 but dcs side it's showing 9.26..

Answer / karthisampath

It may be forced 

Is This Answer Correct ?    6 Yes 0 No

Lube oil pressure transmitter local it's showing 9.8 kg/cm2 but dcs side it's showing 9.26..

Answer / chessor

If u have a proper range... Selection for p.T.. U should have 4 - 20 ma ratio .. U should measure first .. P..T output ... Then check ... Panel side......

And yeh.. Also check ... Pressure transmitter .. Range.. Inserted in dcs parameter range... Both ..

Means... Pt s range same as in dcs parameter.. O/w u will select ans 0 , span screw from transmitter ....

Is This Answer Correct ?    2 Yes 0 No

Lube oil pressure transmitter local it's showing 9.8 kg/cm2 but dcs side it's showing 9.26..

Answer / anish kumaran r

Check with mA .May be the local display .

Is This Answer Correct ?    1 Yes 1 No

Post New Answer

More Instrumentation Interview Questions

for oil & gas industries which zone is normally preferred? why? give its example?

0 Answers  


whats diffeence between dcs & scada operation.

3 Answers   Orchid, Reliance,


How to get Cv of control valve having following parameter ,i.e inlet pressure 4.5kg/cm2 outlet pressure 1 kg/cm2 specific gravity 0.808

3 Answers  


the pump holds on run indication into the dcs and filed local control panel remote push button condition operaton wrong like when the push button pushing conditions the pump is off and the push button release condition the pump is on totally opposite condition . And control room inside give the stop command into dcs just 1secon relay engage and again normal condition. How can I slove

0 Answers  


What is glanding

1 Answers  






please suggest me, how can i change the display setting in term of unit in place of % of Honeywell pressure transmitter ST3000S100?

2 Answers  


What is the use of double seated valve?

0 Answers  


why most of the DP transmitters using maximum range as 0-2500mmwc?why not 1000 2000 3000 4000mmwc

2 Answers   SPIC, TNPL,


what is modbus & what signals are taken through it

2 Answers  


HELLO FRENDS ,, I M IN THE MIDST OF TROUBLE .. JUST LITTLE HELP ME... SUPPOSE ,, I HAVE A CLOSE VESSELE TANK ( HEXANE MEDIA ) ,, I M USING ROSEMOUNT 2051 DPT FOR LEVEL APPLICATION .. ITS CALIBRATE RANGE IS.. . 0 TO 950 MMH20 ..I DID CALIBRATED DPT WITHOUT REMOVING IMPULSE LINE OF HIGH AND LOW TAPPING.. & WITHOUT DISTURB 3 WAY MANIFOLD..!!! BUT ,,, DURING CALIBRATION I SELECT RANGE BY HART LRV IS 900 MMH20 & URV IS 1300 MMH20 ,, BUT ,TANK LEVEL SOMETIMES 100 % AT 1100 MMH20 , SOMETIMES 1300 MMH20 ..IN THIS CONDITION .. WHOLE LOOP FAILED ,, MAIN THING IS THAT ,, HOW TO CUSTOME RANGE SELECT ?? AND IF I USED RANGE OVER THE ORIGINAL CALIBRATE RANGE ,,,THEN WHAT ERROR WILL BE COME ??? HOW TO ZERO CALIBRATION OF DPT... HOW TO ZERO TRIM BY MANIFOLD ?? AND FOR TANK LEVEL PURPOSE ... WHICH UNIT I CAN USE ??? IS THERE ANY CALCULATION OR CALIBRATION .. IF YEH .. THEN PLZ JUST GIVE ME CALIBRATION STEPS FOR DPT.. THANKS YOURSSSSSSS

1 Answers   Torrent Pharma,


What is frequency factor in massflow meter? When using frequency output?

0 Answers   PCMIL,


what is pico fuse? how this different rom othe fuses and how to locate it inside the card?

1 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5084)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16631)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1094)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)