ALLInterview.com :: Home Page            
 Advertise your Business Here     
Browse  |   Placement Papers  |   Company  |   Code Snippets  |   Certifications  |   Visa Questions
Post Question  |   Post Answer  |   My Panel  |   Search  |   Articles  |   Topics  |   ERRORS new
   Refer this Site  Refer This Site to Your Friends  Site Map  Bookmark this Site  Set it as your HomePage  Contact Us     Login  |  Sign Up                      
Google
   
 
Categories >> Engineering >> Electrical Engineering
 
 


 

 
 Civil Engineering interview questions  Civil Engineering Interview Questions (3152)
 Mechanical Engineering interview questions  Mechanical Engineering Interview Questions (3305)
 Electrical Engineering interview questions  Electrical Engineering Interview Questions (13477)
 Electronics Communications interview questions  Electronics Communications Interview Questions (2395)
 Chemical Engineering interview questions  Chemical Engineering Interview Questions (424)
 Aeronautical Engineering interview questions  Aeronautical Engineering Interview Questions (77)
 Bio Engineering interview questions  Bio Engineering Interview Questions (17)
 Metallurgy interview questions  Metallurgy Interview Questions (80)
 Industrial Engineering interview questions  Industrial Engineering Interview Questions (166)
 Instrumentation interview questions  Instrumentation Interview Questions (2408)
 Automobile Engineering interview questions  Automobile Engineering Interview Questions (109)
 Mechatronics Engineering interview questions  Mechatronics Engineering Interview Questions (38)
 Marine Engineering interview questions  Marine Engineering Interview Questions (45)
 Power Plant Engineering interview questions  Power Plant Engineering Interview Questions (81)
 Engineering AllOther interview questions  Engineering AllOther Interview Questions (1205)
Question
Why dose voltage rated at 11kva
 Question Submitted By :: Electrical-Engineering
I also faced this Question!!     Answer Posted By  
 
Answer
# 1
Most of the voltages in the power system are rated at
11kv,132kv or likewise.It is observed that these voltages
are a multiple of 11.This is because of the form factor
which is equal to 1.1 in the equation for the emf generated
by the alternator.Since the form factor is a multiple of 11
most of the voltages assume forms like 11kv,132kv or 220kv.
 
Is This Answer Correct ?    1 Yes 1 No
Abhishek Pandey
 

 
 
 
Other Electrical Engineering Interview Questions
 
  Question Asked @ Answers
 
what is F.A.P in fire alarming system?   3
what is reactive power is it good or bad for a system   4
want to know about DMRC   4
We wish to test 60 Hz systems from a 50 Hz supply. To acheive frequency conversion, we use a VFD. The VFD powers 40 kVA transformer, which has motor and non-motor loads on it. Will the transformer work? Suzlon 2
cause of failure of transformer bushes   2
why skin effect is decreases with decrease with frequency? why skin effect occur Kirloskar 5
why we use dc motor instead of ac motor? Air-Force 7
Hi How can you start-up the 40w tube lite with 230v AC/DC without using any choke/Coil.   5
what voltage to be select in megger for insulation resistance testing to L.V , H.T cables,motors and transfomer?and ohms valve should be giga ohms only or what?   1
To check the earth condition (In plug points); the voltage between earth and Neutral is in below 5 volts. Is it correct   6
if There is Short circuit in Power Transformer, what will happened to Buchholz Relay.?? How Buchholz Relay will respond.??   2
why we use the fuse in only one wire? althrough in ac current the current flows in both directions. why the neutral wire can be taken half the magnitude of phase wire while same current returns from neutral wire?   2
 
For more Electrical Engineering Interview Questions Click Here 
 
 
 
 
 


   
Copyright Policy  |  Terms of Service  |  Articles  |  Site Map  |  RSS Site Map  |  Contact Us
   
Copyright 2013  ALLInterview.com.  All Rights Reserved.

ALLInterview.com   ::  KalAajKal.com