In a 3Ph induction motor(old) 6 wires came out from terminal & not me

Advertise your Business Here

Refer this Site

Login | Sign Up


	SiteMap shows list of All Categories in this site.

Categories >> Engineering >> Electrical Engineering

Civil Engineering Interview Questions

Mechanical Engineering Interview Questions

Electrical Engineering Interview Questions

Electronics Communications Interview Questions

Chemical Engineering Interview Questions

Aeronautical Engineering Interview Questions

Bio Engineering Interview Questions

Metallurgy Interview Questions

Industrial Engineering Interview Questions

Instrumentation Interview Questions

Automobile Engineering Interview Questions

Mechatronics Engineering Interview Questions

Marine Engineering Interview Questions

Power Plant Engineering Interview Questions

Engineering AllOther Interview Questions

Question

In a 3Ph induction motor(old) 6 wires came out from terminal 
& not mentioned u1,v1,w1,u2,v2 & w2.   how can find out the 
terminals?  how can connect to star delta starter??

Question Submitted By :: Subbu

I also faced this Question!!

Rank

Answer Posted By

Re: In a 3Ph induction motor(old) 6 wires came out from terminal & not mentioned u1,v1,w1,u2,v2 & w2. how can find out the terminals? how can connect to star delta starter??

Answer
# 1

first of all you have to use multimeter to identify the
coil teminals. segregate it in two lines as 2 x 3 . ie top
3 terminals and bottom 3 terminals.

Next take a Small DC power supply with 3 volt and a
milliampere meter( DC ). connect this voltage to one of the
coils with milliampere meter in series( Milliampere meter
should be of center zero type ) close the supply voltage to
the coil with make and break it immediately. observe the
deflection whether it is on forward side or reverse side.
and mark one terminal for whcih +ve suplly is connected as
Start and the other ( _ ve )end as Finish. do this
process for other two coils also. once you know the top 3
start points and finish points of the coil. you are almost
there. now you short ckt all finish ends. you are left
with 3 start terminals. ie your STAR connection.

For Delta connection connect finish end of the first coil
to start end of the second coil, finish end of second coil
to start end of third coil and finish end of 3third coil
to start end of first coil. now you have theree junctions.
now your connection is in Delta mode.

Is This Answer Correct ?

9 Yes

0 No

Raovasuki17
[Bonar Emirates]

Question	Asked @	Answers
Other Electrical Engineering Interview Questions


what's transient & sub- transient reactance means?		2
what are the units of cable insulation?		3
what is AB switch???	Simplex	4
How does a star connection and delta connection work? How does the star connection save starting current and how does it change to delta?		2
What is the acceptable earth resistance for Commissioning the Transformer?	HSL	6
WHAT IS THE CONDITION FOR OPERATING DIFFERENTIAL RELAY IN POWER TRANSFORMER & WHERE IS NEUTRAL CT PLACED IN TRANSFORMER		2
I have 30KW Motor Starter Panel, System voltage is 480V, So i have to convert voltage 480 to 220V to give the contactor coil. How i can select control transformer, Which rating transformer i can use this panel, what is the procedure, please tell me.		2
what will happen if ac power supply is given to the rotor of an alternator	Goldman-Sachs	1
How the starter control the starting current in three phase AC Motor?(In DC apply the reistance).		6
WHY MOSTLY BATTERY VOLTAGE IS IN MULIPLE OF 2 LIKE 2V,4V,8V,16V,18V....	Exide	2
protection used for alternator , feeder , transmission line	NHPC	3
How to calculate Busbar Thickness for Different type of HT/LT panels		1

For more Electrical Engineering Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2012 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com