ALLInterview.com :: Home Page            
 Advertise your Business Here     
Browse  |   Placement Papers  |   Company  |   Code Snippets  |   Certifications  |   Visa Questions
Post Question  |   Post Answer  |   My Panel  |   Search  |   Articles  |   Topics  |   ERRORS new
   Refer this Site  Refer This Site to Your Friends  Site Map  Bookmark this Site  Set it as your HomePage  Contact Us     Login  |  Sign Up                      
Google
   
 
Categories >> Engineering >> Mechanical Engineering
 
 


 

 
 Civil Engineering interview questions  Civil Engineering Interview Questions (3015)
 Mechanical Engineering interview questions  Mechanical Engineering Interview Questions (3272)
 Electrical Engineering interview questions  Electrical Engineering Interview Questions (13227)
 Electronics Communications interview questions  Electronics Communications Interview Questions (2349)
 Chemical Engineering interview questions  Chemical Engineering Interview Questions (407)
 Aeronautical Engineering interview questions  Aeronautical Engineering Interview Questions (77)
 Bio Engineering interview questions  Bio Engineering Interview Questions (16)
 Metallurgy interview questions  Metallurgy Interview Questions (79)
 Industrial Engineering interview questions  Industrial Engineering Interview Questions (162)
 Instrumentation interview questions  Instrumentation Interview Questions (2319)
 Automobile Engineering interview questions  Automobile Engineering Interview Questions (104)
 Mechatronics Engineering interview questions  Mechatronics Engineering Interview Questions (38)
 Marine Engineering interview questions  Marine Engineering Interview Questions (43)
 Power Plant Engineering interview questions  Power Plant Engineering Interview Questions (73)
 Engineering AllOther interview questions  Engineering AllOther Interview Questions (1190)
Question
write the formula for finding dimension of bearing from bearing number
 Question Submitted By :: Tapan.aparichit
I also faced this Question!!     Rank Answer Posted By  
 
  Re: write the formula for finding dimension of bearing from bearing number
Answer
# 1
Inner Dia of bearing is
Last two Digit Bearing number X 5
 
Is This Answer Correct ?    74 Yes 9 No
Pavan Kaneria
 
  Re: write the formula for finding dimension of bearing from bearing number
Answer
# 2
Last two digit of bearing number shall be multiplied by 5
which is a shaft size.
 
Is This Answer Correct ?    48 Yes 4 No
T.c.patil
 
 
 
  Re: write the formula for finding dimension of bearing from bearing number
Answer
# 3
1. What is mean by 6205 ZZ

a.6 is the type code, which shows it is a single-row ball
bearing, 2 is the series, means light, 03 is the bore, which
is 17 mm and ZZ is the suffix meaning double shielded bearing.

________________________________________
First two Digit from left indicates bore dia i.e 03 - means
17 mm bore diameter
third digit indicates series like heavy, medium light &
extra light duty - load carrying bearing here its medium
capacity bearing
Last or forth digit shows types of bearing here its Single
row ball bearing
ZZ indicates double shielded bearing


Here is some information on bearing types and nomenclature
that I thought
everyone might enjoy. If you know the bearing number, you
don't need to go to
the dealer, just go to a local bearing distributor or a
place that sells gear
boxes. They should have them or be able to get them in a day.

A bearing number has four parts to it which includes four
numbers and a set of
letters. Each of the first two numbers stand for something,
the last two
designate size. The letters dictate the variation of the
bearing. These letters
can also be followed by more letters designating internal
clearance. In detail:

First number (will be a 1-7) designates the bearing type:
1 = Double Row self-aligning
2 = Double Row self-aligning (wide)
3 = Double Row
4 = Angular Contact
6 = Single Row Deep Groove
7 = Angular Contact

The second number designates the series, or cross section.
This is basically
equivalent to the second number of a tire rating, it's a
ratio of the bore to
the width of the bearing, which also controls the O.D. of
the bearing. The
larger the cross section, the larger the O.D. of the bearing.
18 = Thin Section, Light
19 = Thin Section, Medium
0 = Very Light
2 = Light
3 = Medium
4 = Heavy

The third number (which is a set of two numbers) indicates
the bore (in mm) of
the bearings. All bearings are designated with metric
standards, not inches.
Numbers are as follows:
00 = 10 mm
01 = 12 mm
02 = 15mm
03 = 17 mm
For 20-480mm bore bearings: Last 2 digits x 5 = Bore (mm)
i.e.- if the bearing number was 04 (04 x 5 = 20 mm), 05 (05
x 5 = 25 mm)

The letters after the number indicate the variation. These
change from
manufacturer to manufacturer, but here are some of the
common ones:

Plain -- No Shield
Type Z -- One Shield (normally will have metal shields)
Type 2Z -- Two Shields (one on each side)
Type RS1 -- One Seal (normally the R indicates rubber)
Type 2RS1 --Two Seals (one on each side)
Type LL -- Two Seals (just another manufacturer's designation)
CD -- 15 degree contact angle (for angular contact)
ACD = 25 degree contact angle (for angular contact)

The bearings can also have a C2, C3, C4 or C5 designation
after the bearing
number. This indicates that the internal fit (the inner race
to ball to outer
race) is not standard. If your bearing has one of these
designators, make sure
you get a bearing with the same designator. A C2 is less
than standard
clearance, while a C3, 4, and 5 are larger than standard.
 
Is This Answer Correct ?    24 Yes 2 No
Rapeti Hari Hara Kumar
 
  Re: write the formula for finding dimension of bearing from bearing number
Answer
# 4
Ball Bearing 6301 
Is This Answer Correct ?    28 Yes 5 No
Hanif
 
  Re: write the formula for finding dimension of bearing from bearing number
Answer
# 5
it will vary from ID to ID( means up to 10 it has direct
value after 10 mm dia it has caliculation of last two digits
multiply by 5
 
Is This Answer Correct ?    15 Yes 1 No
Hari
 

 
 
 
Other Mechanical Engineering Interview Questions
 
  Question Asked @ Answers
 
What is seamless pipe   4
what is toughest metal to weld of tungston or cast iron?   1
Names the valve connected in cylinder head of the engine.   2
sir i need ongc old technical test papers can u send me immediately ONGC 1
PLZ SEND QUESTIONS OF MRF...URGENT........PLZ YAAAAR.... MRF 3
hi friends, i want to know full depth of regarding mechanical seals   1
welding electrodes consumption   1
Dear all, How will we calculate the Diesel engines ( generator) efficiency considering fuel   1
Tell me about a problem you had with a supervisor Petro-Star-Mount 1
On 22nd December, which of the following places has the largest day and shortest night ?   2
what is work done in throttling process.   3
Can we use pure oxygen in IC engines instead of air?? what would be the advantages and disadvantages of using it?? Have any steps been taken about this?? TATA 4
 
For more Mechanical Engineering Interview Questions Click Here 
 
 
 
 
 


   
Copyright Policy  |  Terms of Service  |  Articles  |  Site Map  |  RSS Site Map  |  Contact Us
   
Copyright 2013  ALLInterview.com.  All Rights Reserved.

ALLInterview.com   ::  KalAajKal.com