ALLInterview.com :: Home Page            
 Advertise your Business Here     
Browse  |   Placement Papers  |   Company  |   Code Snippets  |   Certifications  |   Visa Questions
Post Question  |   Post Answer  |   My Panel  |   Search  |   Articles  |   Topics  |   ERRORS new
   Refer this Site  Refer This Site to Your Friends  Site Map  Bookmark this Site  Set it as your HomePage  Contact Us     Login  |  Sign Up                      
Google
   
 
Categories >> Engineering >> Electrical Engineering
 
 


 

 
 Civil Engineering interview questions  Civil Engineering Interview Questions (3113)
 Mechanical Engineering interview questions  Mechanical Engineering Interview Questions (3298)
 Electrical Engineering interview questions  Electrical Engineering Interview Questions (13416)
 Electronics Communications interview questions  Electronics Communications Interview Questions (2382)
 Chemical Engineering interview questions  Chemical Engineering Interview Questions (420)
 Aeronautical Engineering interview questions  Aeronautical Engineering Interview Questions (77)
 Bio Engineering interview questions  Bio Engineering Interview Questions (17)
 Metallurgy interview questions  Metallurgy Interview Questions (80)
 Industrial Engineering interview questions  Industrial Engineering Interview Questions (165)
 Instrumentation interview questions  Instrumentation Interview Questions (2393)
 Automobile Engineering interview questions  Automobile Engineering Interview Questions (107)
 Mechatronics Engineering interview questions  Mechatronics Engineering Interview Questions (38)
 Marine Engineering interview questions  Marine Engineering Interview Questions (45)
 Power Plant Engineering interview questions  Power Plant Engineering Interview Questions (78)
 Engineering AllOther interview questions  Engineering AllOther Interview Questions (1202)
Question
State the function of control rods used in nuclear reactor
 Question Submitted By :: Electrical-Engineering
I also faced this Question!!     Answer Posted By  
 
Answer
# 1
control rods are used to control nuclear fission in reactor.
There is one mechanism for rod by this rod can travel
uoward and downward direction. When rod are fully inserted
fission process is stop. By continuos control of this rod
fission process is contr0led.........
 
Is This Answer Correct ?    2 Yes 0 No
Chirag
 

 
 
 
Other Electrical Engineering Interview Questions
 
  Question Asked @ Answers
 
How to increase home power factor? Can we connect capacitor directly? How to select capacity of capacitor?   5
when is the OHMS LAW IS APPLICABLE? ABB 9
what are eddy currents   1
why do we prefer a 3-phase delta connected load rather than star connected?   4
What is different between Regulator & Stabilizer?   5
why we ground the scondary of current transformer.   3
IF 3 NOS.OF HEATERS,3KW CAPACITY EACH,1 NO.HEATER CONNECTED IN R PHASE,1 IN Y PHASE AND 1 IN B PHASE.THEIR END POINTS CONNECTED IN STAR.IF I CONNECT THIS STAR POINT TO NEUTRAL OR DO NOT CONNECT TO NEUTRAL.WHAT WILL THE DIFFERENCE.   3
why CT output is always raetd 5.regardsof primery curre. ABB 2
We have two 1 phase heating coils having same resistance of 25ohm, but during operation one takes 3A and other 6A Is it posiible Pls. explain Bhel 5
a room heater is connected in serise with a 100w bulb.if the 100w bulb is replaced by a 40w bulb then the output of the heater is increase/decrease/remain same?   8
a 3 phase slip ring induction motor is wound for 4 poles on stator and 6 poles on rotor; when 3 phase balanced voltage source at 50 hz is applied to motor it will run at a)1500rpm b)1000rpm c)750 rpm d)zero rpm Essar 11
Why the CT Secondary is rated as 5A generally?   2
 
For more Electrical Engineering Interview Questions Click Here 
 
 
 
 
 


   
Copyright Policy  |  Terms of Service  |  Articles  |  Site Map  |  RSS Site Map  |  Contact Us
   
Copyright 2013  ALLInterview.com.  All Rights Reserved.

ALLInterview.com   ::  KalAajKal.com