ALLInterview.com :: Home Page            
 Advertise your Business Here     
Browse  |   Placement Papers  |   Company  |   Code Snippets  |   Certifications  |   Visa Questions
Post Question  |   Post Answer  |   My Panel  |   Search  |   Articles  |   Topics  |   ERRORS new
   Refer this Site  Refer This Site to Your Friends  Site Map  Bookmark this Site  Set it as your HomePage  Contact Us     Login  |  Sign Up                      
Google
   
 
Categories >> Engineering >> Electrical Engineering
 
 


 

 
 Civil Engineering interview questions  Civil Engineering Interview Questions (3078)
 Mechanical Engineering interview questions  Mechanical Engineering Interview Questions (3289)
 Electrical Engineering interview questions  Electrical Engineering Interview Questions (13332)
 Electronics Communications interview questions  Electronics Communications Interview Questions (2363)
 Chemical Engineering interview questions  Chemical Engineering Interview Questions (416)
 Aeronautical Engineering interview questions  Aeronautical Engineering Interview Questions (77)
 Bio Engineering interview questions  Bio Engineering Interview Questions (17)
 Metallurgy interview questions  Metallurgy Interview Questions (79)
 Industrial Engineering interview questions  Industrial Engineering Interview Questions (163)
 Instrumentation interview questions  Instrumentation Interview Questions (2381)
 Automobile Engineering interview questions  Automobile Engineering Interview Questions (106)
 Mechatronics Engineering interview questions  Mechatronics Engineering Interview Questions (38)
 Marine Engineering interview questions  Marine Engineering Interview Questions (43)
 Power Plant Engineering interview questions  Power Plant Engineering Interview Questions (77)
 Engineering AllOther interview questions  Engineering AllOther Interview Questions (1196)
Question
How much should be the specific gravity of a DG set battery
Electrolyte.
 Question Submitted By :: Electrical-Engineering
I also faced this Question!!     Answer Posted By  
 
Answer
# 1
The SG should be 1200 when it is fully charged.. for over
charged it is > 1200, and less than 1200 for discharging.
The SG will vary with temp. (increases with temp.)
 
Is This Answer Correct ?    5 Yes 0 No
Shariff
 
Answer
# 2
1200 to 1230 as such normal battery electrolyte. 
Is This Answer Correct ?    4 Yes 1 No
N.venkidusamy
 
 
 

 
 
 
Other Electrical Engineering Interview Questions
 
  Question Asked @ Answers
 
In a 3 phase squirrel cage induction motor why does rotor rotate? will 3 phase transformer rotate like a motor if it is placed on bearings and powered up? give reason Siemens 10
how we calculate the motor rating of pump for water suction ?its any formula for that plz give thank u   3
How to find the maximum load, that can be supplied by a transformer..... ME 2
What will happen when more than one star neutral points at same voltage level are connected to earth by metallic conductor?   1
check list for anuval maintatince check list of oil transforms   2
how can we measure 220kv or more than these voltages ...?and also how can we conform whether we r getting 220kv from generating stations throuth the h v transmission lines?   1
As per principle we say in three phase supply ,the voltage is producing by phase angle between two phase so two phase is needed means then why we using three phase ?   2
if we keep frequency constant can we cal a synchronous generator as a dc generator Cummins 2
can we use inductor in case of d.c.,if yes then what will happen in circuit JSW 3
At 765Kv, I have seen the use of PT at line side for metering and CVT for protection, although as far as my knowledge is concern, PT at this voltage level will have huge loss and more cost as compared to CVT as CVT can also perform same function of Protection and Metering? So my question is why use PT and not CVT for metering and protection in order to reduce the cost.   1
1 kva how much amps? How to calculate ? L&T 2
During Load testing of battery charger with temporary AC Generator .When reach 70% load Generator immediately shutdown .we could not able to Recognize ,what is exactly problem .Please kindly clarify us   1
 
For more Electrical Engineering Interview Questions Click Here 
 
 
 
 
 


   
Copyright Policy  |  Terms of Service  |  Articles  |  Site Map  |  RSS Site Map  |  Contact Us
   
Copyright 2013  ALLInterview.com.  All Rights Reserved.

ALLInterview.com   ::  KalAajKal.com