ALLInterview.com :: Home Page            
 Advertise your Business Here     
Browse  |   Placement Papers  |   Company  |   Code Snippets  |   Certifications  |   Visa Questions
Post Question  |   Post Answer  |   My Panel  |   Search  |   Articles  |   Topics  |   ERRORS new
   Refer this Site  Refer This Site to Your Friends  Site Map  Bookmark this Site  Set it as your HomePage  Contact Us     Login  |  Sign Up                      
Google
   
 
Categories >> Engineering >> Mechanical Engineering
 
 


 

 
 Civil Engineering interview questions  Civil Engineering Interview Questions (3154)
 Mechanical Engineering interview questions  Mechanical Engineering Interview Questions (3306)
 Electrical Engineering interview questions  Electrical Engineering Interview Questions (13483)
 Electronics Communications interview questions  Electronics Communications Interview Questions (2395)
 Chemical Engineering interview questions  Chemical Engineering Interview Questions (424)
 Aeronautical Engineering interview questions  Aeronautical Engineering Interview Questions (77)
 Bio Engineering interview questions  Bio Engineering Interview Questions (17)
 Metallurgy interview questions  Metallurgy Interview Questions (80)
 Industrial Engineering interview questions  Industrial Engineering Interview Questions (166)
 Instrumentation interview questions  Instrumentation Interview Questions (2409)
 Automobile Engineering interview questions  Automobile Engineering Interview Questions (109)
 Mechatronics Engineering interview questions  Mechatronics Engineering Interview Questions (38)
 Marine Engineering interview questions  Marine Engineering Interview Questions (45)
 Power Plant Engineering interview questions  Power Plant Engineering Interview Questions (81)
 Engineering AllOther interview questions  Engineering AllOther Interview Questions (1207)
Question
what is the purpose of wear rings in centrifugal pumps ?
 Question Submitted By :: Mechanical-Engineering
I also faced this Question!!     Answer Posted By  
 
Answer
# 1
Wear rings can be defined as a device used to seal the
pressure leakage of the liquid between the inlet of the
impeller and the pump casing. Wear rings are typically
found on pumps with closed impellers. A similar device that
serves the same function called a wear plate can be found
on some pumps with a semi-open impeller.
The typical reason for using a wear ring is to decrease the
amount of leakage loss around the impeller. Due to more
work available to push the pumped liquid out the discharge
there is a slight improvement in pump efficiency.
 
Is This Answer Correct ?    23 Yes 1 No
Bibhudatta Behera
 
Answer
# 2
The wear rings have three purposes to serve, 1. To decrease
the discharge fluid leak to the suction area and maintain
the pumps efficiency. 2. It acts as a bearing in a
multistage centrifugal pumping system. 3. It is economical
to replace the wear rings rather than replacing the
expensive impellers in case of any mechanical damage such
as, wear and tear due to abrassion or any other reasons.
 
Is This Answer Correct ?    23 Yes 3 No
Soman Nair
 
 
 
Answer
# 3
Wear ring is act as a boundary in a centrifugal pumps
between low pressure (Vacuum) area and high pressure area.
Its also supports impeller's load after bearing failure or
damage and save other parts of pumps
 
Is This Answer Correct ?    1 Yes 0 No
Mahesh Kumar Pachauri
 

 
 
 
Other Mechanical Engineering Interview Questions
 
  Question Asked @ Answers
 
What are the loads considered when designing the Nut and Bolts?   12
What motivates you to do a good job? Maruti-Suzuki 6
What is the normal Ph value of boiler water RRB 2
What are the lubricating system of an IC engine?   9
what is mean nx6   2
i woule my experiences in BARC i recently gone for the interview.. they dont consider u r dress code and all, even u can go in a jeans and tea shirt.they dont careabout u r personality , profile .. Theytest (complety) our technical knowledge.. so u have to prepare well in not only the basics but also in depth.. Even the did not consider the percentile in GATE.. One guy got 99.63 in gate but did not given medical. so u have to be very stiff and togh technically.. u should have a lot of luck too,because right panel selects u.. u dont expect what,how in Barc,only why.i amnot frightening u, i am telling u some facts i have faced.. istead of all i did it superbly and waiting for the result.. if u want more information, u can email me ,call me at any time.. BARC 31
Pls send me the 10 years technical question paper of Jindal steel power to my email id Jindal 12
what is the minimum gear ratio? Bosch 2
What type of beari ng u will prefer for automobile? TVS 2
If one cylinder of a diesel engine receives more fuel than the others, then for that cylinder the: a) exhaust will be smoky b) piston rings would stick into piston grooves c) exhaust temperature will be high d) engine starts overheating e) all of the above. Bhel 7
what is the difference between dross and scale? Hindalco 1
describe yourself Tech-Mahindra 2
 
For more Mechanical Engineering Interview Questions Click Here 
 
 
 
 
 


   
Copyright Policy  |  Terms of Service  |  Articles  |  Site Map  |  RSS Site Map  |  Contact Us
   
Copyright 2013  ALLInterview.com.  All Rights Reserved.

ALLInterview.com   ::  KalAajKal.com