ALLInterview.com :: Home Page            
 Advertise your Business Here     
Browse  |   Placement Papers  |   Company  |   Code Snippets  |   Certifications  |   Visa Questions
Post Question  |   Post Answer  |   My Panel  |   Search  |   Articles  |   Topics  |   ERRORS new
   Refer this Site  Refer This Site to Your Friends  Site Map  Bookmark this Site  Set it as your HomePage  Contact Us     Login  |  Sign Up                      
Google
   
 
Categories >> Engineering >> Mechanical Engineering
 
 


 

 
 Civil Engineering interview questions  Civil Engineering Interview Questions (3082)
 Mechanical Engineering interview questions  Mechanical Engineering Interview Questions (3290)
 Electrical Engineering interview questions  Electrical Engineering Interview Questions (13338)
 Electronics Communications interview questions  Electronics Communications Interview Questions (2363)
 Chemical Engineering interview questions  Chemical Engineering Interview Questions (416)
 Aeronautical Engineering interview questions  Aeronautical Engineering Interview Questions (77)
 Bio Engineering interview questions  Bio Engineering Interview Questions (17)
 Metallurgy interview questions  Metallurgy Interview Questions (80)
 Industrial Engineering interview questions  Industrial Engineering Interview Questions (163)
 Instrumentation interview questions  Instrumentation Interview Questions (2382)
 Automobile Engineering interview questions  Automobile Engineering Interview Questions (106)
 Mechatronics Engineering interview questions  Mechatronics Engineering Interview Questions (38)
 Marine Engineering interview questions  Marine Engineering Interview Questions (44)
 Power Plant Engineering interview questions  Power Plant Engineering Interview Questions (78)
 Engineering AllOther interview questions  Engineering AllOther Interview Questions (1196)
Question
What is the Difference between COTTER JOINT & KNUCKLE JOINT?
 Question Submitted By :: Mechanical-Engineering
I also faced this Question!!     Answer Posted By  
 
Answer
# 1
motion ccan transferred in all degrees is called knuckle
joint, & only in one direction is called cooter joint
 
Is This Answer Correct ?    40 Yes 6 No
Kgm
 
Answer
# 2
Knuckle joint is used to connect two rods whose axes either coincide or intersect and lie in one plane, which are subjected to transmit axial TENSILE force on other hand cotter joint is used to connect two co-axial rods, which are subjected to either axial force or axial compressive force. 
Is This Answer Correct ?    28 Yes 1 No
Sahil
 
 
 
Answer
# 3
knuckle use knukle pin to hold two shafts bt cotter use a cotter 
Is This Answer Correct ?    2 Yes 3 No
Karan
 
Answer
# 4
cotter joint are used for compressive force only while
knuckle are primarily used or tensile force
 
Is This Answer Correct ?    11 Yes 16 No
Sudipto Raj
 
Answer
# 5
i think both transmit axial tensile force only.. 
Is This Answer Correct ?    4 Yes 18 No
Sameer
 

 
 
 
Other Mechanical Engineering Interview Questions
 
  Question Asked @ Answers
 
difference between performance and efficiency?   13
how much safty of chiller?   1
HOW TO CALCULATE CV VALUE / KV VALUE OF A STRAINER   3
what is spherical surface contact and midsplit surface clearance regarding to turbine. Bhel 2
difference between steam hammering and water hammering   5
what is cswip?   2
How to calculate the moment of inertia for a circuit board?   1
what is mean by DBSE? Sabic 1
what is the disadvantages of transformer type welding machine L&T 1
For maximum capacity of compressor inlet temperature of air should be high, low, very high. BEL 7
What is the deff betwen Two stroke engine & Four stroke engines. Difine Theoretcally & Practically.   11
ice can float on the surface of water?   3
 
For more Mechanical Engineering Interview Questions Click Here 
 
 
 
 
 


   
Copyright Policy  |  Terms of Service  |  Articles  |  Site Map  |  RSS Site Map  |  Contact Us
   
Copyright 2013  ALLInterview.com.  All Rights Reserved.

ALLInterview.com   ::  KalAajKal.com