What is the difference between Is 2062 material Grade A &
B. Which grade is better ?



What is the difference between Is 2062 material Grade A & B. Which grade is better ?..

Answer / mukund

CARBO PERCENTAGE :GR A -0.23,GRB-0.22,GR C 0.20
WELDABILITY INCREASES FROM A TO C
Y GRROVE CRACKABILITY TEST ONLY FOR GR C.
IMPACT TEST IS NOT DONE FOR GRADE A

Is This Answer Correct ?    34 Yes 2 No

Post New Answer

More Mechanical Engineering Interview Questions

water balance calculation for 1X500 tpd DRI plant?

0 Answers   NBVL,


Sir we wants to const ruct a wall,size wall is 50x30x9/12' feet.how many bricks required. Please advise

0 Answers  


What do u mean about Gear Coupling Number like 101,102,103.....110,112....and how u will get proper Number of Gear Coupling.,Explain it.

2 Answers   TATA,


application of two stroke engines

4 Answers  


What is Natural frequency of Vibration?. Imagine a circular disk of radius 'r' is oscillating inside a Semi circular ring of radius 'R', how will you find natural frquency of the system?.

2 Answers   College School Exams Tests, IGCAR, Super Max,






Difference between isometric & trimetric view?

1 Answers   ACZ, Descon,


What is fuel catalytic cracking

1 Answers   RRB,


Define representative elementary volume?

0 Answers  


What will you do in case of scavenging fire

0 Answers  


What is the purpose of engine preheating?

1 Answers  


Why we need two angle of projections ( 1st angle and 3rd angle)? Cant we standardize to one.

2 Answers   Hyundai,


2. Dry saturated steam at 3.5 bar is expanded through a convergent nozzle to 2.2 bar. The exit area is 5 sq. cm. Calculate the exit velocity and mass flow rate, assuming isentropic expansion and super saturated flow. b) A cast iron cylinder head is fastened to a cylinder of 750mm bore with 12 stud bolts. The maximum pressure inside the cylinder is 3 Mpa. The stiffness of part is thrice the stiffness of the bolt. What should be the initial tightening load so that the point is leak proof at maximum pressure? Also choose a suitable bolt for the above application 2 The propeller shaft of a marine engine is to transmit 600 kW at 1200 rpm, without a significant bending. The efficiency of the propeller is 88% at 32 knots ( 1 knot = 1085 km/hr). If the slenderness ratio is less than 50 and the permissible shear stress should not exceed 65 Mpa. Determine the diameter of shaft. 3 A semi-elliptic leaf spring consists of two extra full-length leaves and six graduated length leaves, including the master leaf. Each leaf is 7.2 mm thick and 65 mm wide. The centre-to-centre distance between the two eyes is 1.3m. The leaves are pre-stressed in such a way that when the load is maximum, stress induced in all leaves are equal to 380 N/mm sq. Determine the maximum force that the spring can withstand

0 Answers  


Categories
  • Civil Engineering Interview Questions Civil Engineering (5084)
  • Mechanical Engineering Interview Questions Mechanical Engineering (4451)
  • Electrical Engineering Interview Questions Electrical Engineering (16631)
  • Electronics Communications Interview Questions Electronics Communications (3918)
  • Chemical Engineering Interview Questions Chemical Engineering (1094)
  • Aeronautical Engineering Interview Questions Aeronautical Engineering (239)
  • Bio Engineering Interview Questions Bio Engineering (96)
  • Metallurgy Interview Questions Metallurgy (361)
  • Industrial Engineering Interview Questions Industrial Engineering (259)
  • Instrumentation Interview Questions Instrumentation (3014)
  • Automobile Engineering Interview Questions Automobile Engineering (332)
  • Mechatronics Engineering Interview Questions Mechatronics Engineering (97)
  • Marine Engineering Interview Questions Marine Engineering (124)
  • Power Plant Engineering Interview Questions Power Plant Engineering (172)
  • Textile Engineering Interview Questions Textile Engineering (575)
  • Production Engineering Interview Questions Production Engineering (25)
  • Satellite Systems Engineering Interview Questions Satellite Systems Engineering (106)
  • Engineering AllOther Interview Questions Engineering AllOther (1379)