| Other CCDA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What task do you complete to identify organizational
objectives that will reflect your design?
A. Business Objectives
B. Scheduling requirements
C. Vacation time
D. Meetings | | 2 |
| When is the route to a node determined in an SRB (Source
Route Bridging) Token Ring network?
A. Before any data is transmitted
B. After the data is transmitted
C. During the transmission of data
D. After the first frame is transmitted | | 1 |
| Which condition does not create LAN media problems?
A. Protocol doesn?t scale well
B. Long wait for the token
C. Excessive collisions
D. Too many devices | | 1 |
| What would a TE2 device be used for in an ISDN connection?
A. as a connection from an NT1 device to an NT2 device
B. as a connection from a non-ISDN terminal through a TA to
the ISDN network
C. as a connection from four-wire subscriber wiring to the
conventional two-wire local loop
D. as a connection to the ISDN network through a four-wire,
twisted-pair digital link | | 1 |
| Which router would you choose for your design?
A. 1600
B. 1700
C. 3600
D. 3640
E. 7200 | | 1 |
| Which of the following three sets of IP addresses and subnet
masks are private IP addresses?
A. 10.0.0.0 255.0.0.0
B. 172.16.0.0 255.255.0.0
C. 172.16.0.0 255.240.0.0
D. 192.168.0.0 255.255.0.0 | | 1 |
| Which of the following three protocols replace SDLC?
A. 802.2
B. HDLC
C. QLLC
D. X.25 | | 1 |
| What network design is becoming common when there is a
central office with one or more remote locations?
A. ISDN PRI at the central location and ISDN BRI at the
remote locations.
B. Using core routers at all sites
C. Only using access routers
D. Using a full mesh network | | 1 |
| What are the three commonly used methods of flow control
used for handling network congestion?
A. Buffering
B. Source-quench messages
C. Error checking
D. Windowing | | 1 |
| 6. Which of these statements best describes VPLS ?
| Pari-Networks | 1 |
| What are two differences between 10BaseT and 100BaseT?
A. Speed
B. Frame format
C. Addressing
D. Network diameter | | 1 |
| EIGRP was developed to improve what two protocols?
A. OSPF
B. RIP
C. BGP
D. IGRP | | 1 |
| OSPF supports priority routing for which TCP/IP feature?
A. PA
B. TCP
C. IP
D. SNA | | 1 |
| What protocol advertises Netware services to network
clients? (Type acronym). | | 1 |
| What address is 12 hexadecimal, resides in the Data-Link
layer, and is burned in the ROM by the manufacturer. | | 1 |
| Which two LAN switching features apply to store-and-forward
switches?
A. CRC
B. Frame length
C. Source address
D. Collision Windows | | 1 |
| The following are the four steps in establishing an X.25
virtual circuit. Place them in the correct order.
A. The PSE (Packet Switch Exchange) passes the packet to the
next remote DCE
B. The local DCE packet binder sends packet to the closest
PSE (Packet Switch Exchange)
C. The source DTE sends packet to the local DCE
D. The remote DCE examines the packet header of destination DTE | | 1 |
| Diagramming application information flow is important because:
A. it helps identify heavy traffic paths
B. it helps figure out why email gets from one place to another
C. it can tell you when to purchase a new router
D. it can tell you when to purchase a new switch | | 2 |
| What is the second step when creating a prototype?
A. Develop a test plan
B. Review the customer requirements
C. Investigate what the competition will be proposing
D. Define how big the prototype will be | | 1 |
| Which of the following is not true in regards to route
summarization?
A. It increases the size of the routing table
B. It increases the complexity of the network
C. IP networks must be contiguous to be safely summarized
D. Routing tables must have the capacity to support
classless routing | | 1 |
| |
| For more CCDA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
