What happens when the hold-down timer expires? A. Routes are flushed fro

Advertise your Business Here

Refer this Site

Login | Sign Up


	Do you have a collection of Interview Questions and interested to share with us!! Please send that collection to along with your userid / name. ThanQ

Categories >> Certifications >> Cisco Certifications >> CCDA

CCNA Interview Questions

CCDA Interview Questions

Question

What happens when the hold-down timer expires?

A.	Routes are flushed from the routing table after the flush
timer expires

B.	Routes are flushed from the routing table immediately

C.	Routes are never flushed

D.	A triggered update will reset the hold-down timer

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: What happens when the hold-down timer expires? A. Routes are flushed from the routing table after the flush timer expires B. Routes are flushed from the routing table immediately C. Routes are never flushed D. A triggered update will reset the hold-down timer

Answer
# 1

Answer: D

A triggered update is one of the instances that can reset a
hold-down timer after it expires.

Is This Answer Correct ?

0 Yes

0 No

Guest

Question	Asked @	Answers
Other CCDA Interview Questions


What is the first step in diagramming packet flow for the terminals within a network? A. Identify the end user nodes of all the terminals B. Figure out the speed of all the servers C. Find out where all the routers are located D. Find out where all the switched are located		2
What is the technique used by a router that can automatically initiate and close a circuit-switched session? A. PLP B. LAPP C. ASN.1 D. DDR		1
How does the Spanning Tree Protocol (STP) prevent bridging loops? A. By not allowing any redundant paths within the network B. By calculating the metrics of each path C. By detecting and logically blocking redundant paths from the network D. By creating virtual LANS	HCL	1
What are the five areas of the ISO Network Management Model? A. Performance management B. Accounting management C. Flow management D. Configuration management E. Operating management F. Fault management G. Routing management H. Security management		1
The following are the four steps in establishing an X.25 virtual circuit. Place them in the correct order. A. The PSE (Packet Switch Exchange) passes the packet to the next remote DCE B. The local DCE packet binder sends packet to the closest PSE (Packet Switch Exchange) C. The source DTE sends packet to the local DCE D. The remote DCE examines the packet header of destination DTE		1
What category or categories does Client/Server fit into the following Job Aid? Name of Protocol Type of Protocol # of Users # of Hosts or Servers Comments		1
Match the following devices with the correct description. A. Switch 1. Operates at the physical layer and extends the cable as if it is a single cable. B. Router 2. Operates at the physical layer and connects all connections into one device or concentrator. C. Repeater 3. Operates at the network layer and can filter both hardware and network addresses. D. Hub 4. Works at the Data-Link layer and transmits a digital signal only to the specific port where the destination MAC address is located.		1
What layer of the OSI reference model does TCP reside in? A. Session B. Transport C. Network D. Data-Link		1
What are two true statements regarding DDR (Dial-on-Demand Routing)? A. Allows a router to automatically initiate and end a circuit-switched session B. DDR cannot be configured because it is set with a default configuration C. Can configure it to be used during non-peak hours D. Can only be used with Cisco PIX		1
With Centralized Routing, each node must determine and maintain its routing information independently? A. True B. False		1
What is the second step when creating a prototype? A. Develop a test plan B. Review the customer requirements C. Investigate what the competition will be proposing D. Define how big the prototype will be		1
Regarding a full-mesh network and a partial-mesh network, what is the most accurate statement? A. Split Horizon will not work on a full-mesh network B. A full-mesh network is more expensive because more routers are used C. A partial-mesh network is less expensive because less virtual circuits are used D. Broadcasts are more plentiful on a partial-mesh network		1
When designing a flat switched network you can have: A. the same number of IP and IPX nodes without performance degradation B. more IP than IPX nodes on the same segment C. more IPX than IP nodes on the same segment D. more AppleTalk than IP nodes on the same segment		1
What protocol advertises Netware services to network clients? (Type acronym).		1
When characterizing a network, how many buffer misses should not be exceeded on a Cisco router per hour? A. 10 B. 25 C. 50 D. 100		1
What address is 12 hexadecimal, resides in the Data-Link layer, and is burned in the ROM by the manufacturer.		1
Distance Vector and Link-State protocols converge more quickly if: A. there is router redundancy B. there is router redistribution C. the update interval is set to its maximum D. the whole routing table is sent to announce changes		1
What AppleTalk protocol permits AppleTalk workstations to share files across a network?		1
Traffic Shaping does which one of the following? A. Eliminates bottlenecks by throttling back traffic volume at the source or outbound end B. Reduces the frame size so bandwidth is better utilized C. It increases source traffic to a configured bit rate D. Allows you to control hubs and repeaters		1
What set of Frame Relay enhancements offer extensions for managing complex internetworks? A. CMT B. SNMP C. LMI D. RMON		1

For more CCDA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com