| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the 2 characteristics that TCP and UDP share in common?
A.) Both use port numbers to identify upper level applications
B.) Operate at the Network layer
C.) Both are Transport protocols
D.) Both are reliable communications | | 3 |
| Which statement is true regarding Administrative distance?
A.) It is a metric
B.) Number of hops between two routers
C.) Trustworthiness of the routing information
D.) RIP Administrative distance is 100 | TCS | 1 |
| What are the Timer of RIP, IGRP, EIGRP and OSPF Routing
Protocol?
| IBM | 15 |
| How often does IP RIP send out routing table updates by default?
A.) They send complete updates every 30 seconds
B.) They send partial updates every 30 seconds
C.) They send complete updates every 60 seconds
D.) They send partial updates every 60 seconds | | 2 |
| Which statement about half duplex Ethernet operations is true?
A. With half duplex transmission frames feed into a single
cable in one direction at a time.
B. Half duplex transmission between stations is achieved by
using point to point Ethernet and Fast Ethernet connections
C. Half duplex transmission between stations is achieved by
using point to munificent Ethernet and Fast Ethernet connections
D. Half duplex Ethernet technology provides a transmit
circuit connection wired directly to the receiver circuit at
the other end of the connection | | 5 |
| You want a message to be displayed every time someone tries
to log
on to the router. Which command is required to accomplish
this task?
A.) motd#(message)#
B.) banner motd(message)
C.) banner motd#(message)#
D.) banner motd*(message)
E.) banner login#(message)# | | 1 |
| What is the juncture at which the CPE ends and the local loop
portion of the service begins?
A. Demarc
B. CO
C. Local loop
D. Last-mile | | 1 |
| At what layer of the OSI reference model does FRAME-RELAY
map to?
A.) Session
B.) Physical
C.) Network
D.) Presentation
E.) Transport
F.) Datalink | | 1 |
| What is the 5-4-3-2-1 rule of network design? | | 3 |
| What does CCNA stand for?
A. Cisco Certified Network Administrator
B. Cisco Certified Network Associate
C. Certified Circuitry in Networking Apprentice
D. Calico Cats of North America | | 3 |
| What are the three phases of PPP session establishment?
A. Link establishment phase
B. Authentication phase
C. Network layer protocol phase
D. Handshake phase
E. Dial-in phase | | 2 |
| What is true about Link-State protocols?
A.) They maintain a more complex table than distant vector
protocols
B.) They maintain a less complex table than distant vector
protocols
C.) They use routing ports
D.) The maintain backup copies of the IOS | | 1 |
| As the system administrator, you type "ppp authentication
chap pap
secret". Which authentication method is used first in
setting up a session?
A. secret
B. PAP
C. CHAP
D. PPP/SLIP | | 1 |
| Which IP address and wildcard mask would you use in your
ACL to block all the
hosts in the subnet 192.168.16.43/28? | Siemens | 2 |
| What does a router do with a packet that it does not have a
destination network for?
A.) Sends it to the Serial port
B.) Drops the packet
C.) Sends it back out the same interface it received it in
D.) Forwards the packet to the next hop | | 2 |
| What key do you use to view the last command?
A.) Ctrl+X
B.) Ctrl+Z
C.) Ctrl+E
D.) Ctrl+P | | 1 |
| Which statement about the Point to Point Protocol (PPP) is true?
A. PPP supports TCP/IP but not Novell IPX
B. PPP is being phased out of existence by the Serial Line
Internet Protocol (SLIP)
C. PPP providces router to router and host to network
connections over both synchronous and asynchronous circuits
D. PPP is an ITU T and ANSI standard that defines the
process for sending data over a packet switched data network
(PSDN) | | 1 |
| Identify the command to display the IP host table?
A.) show ip hostnames
B.) show ip names
C.) show hosts
D.) show ip hosts | | 1 |
| Which layer is responsible for negotiating data transfer syntax?
A.) Network
B.) Session
C.) Application
D.) Transport
E.) Presentation | | 1 |
| If a router uses static routing, how does it learn the
route to remote networks?
The router uses a RIP request to obtain remote network
numbers.
The router uses a routing protocol to exchange remote
network numbers.
The router uses DNS request packets to obtain remote
network numbers.
The Network Administrator manually configures the remote
networks.
| | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
