| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the length of an IPX address and it's components?
A.) 80 bits, 48 bits network and 32 bits node
B.) 32 bits, 16 bits network and 16 bits node
C.) None of the above
D.) 80 bits, 32 bits network and 48 bits node | | 1 |
| A traffic light is an example of what type of mechanism?
A.) Collision detection
B.) Flow control
C.) Sequence numbering
D.) Network management | | 1 |
| What is the routing algorithm used by RIP and IGRP?
A.) OSPF
B.) Link-state
C.) Dynamic
D.) Distance Vector | | 2 |
| What is the default CDP broadcast update rate for Cisco routers?
A.) 120 seconds
B.) 60 seconds
C.) 30 seconds
D.) 90 seconds | | 1 |
| The -- terminal no editing -- command will perform what
function?
A.) Edit the contents of NVRAM
B.) Allows access to the terminal port
C.) Stops the advanced editing feature
D.) Enable password functions | | 1 |
| Identify 3 characteristics of switches?
A.) Increase available bandwidth
B.) Decrease broadcast traffic
C.) Support full duplex in a multipoint topology
D.) Make forwarding decision using MAC address
E.) Create collision domains | | 1 |
| Why would you use static routing instead of dynamic routing?
A.) When you want automatic updates of the routing tables
B.) All the time
C.) When you have very few routes and want to conserve bandwidth
D.) When you have a gateway of last resort | | 1 |
| Identify 2 features of PPP PAP authentication?
A.) Username and password is sent in clear text
B.) Authentication messages are sent periodically during the
connection
C.) More secure than CHAP
D.) Remote node is control of authentication process | | 1 |
| Identify the command that specifies Serial 0 in slot 1?
A.) Router(config)# interface serial1/1
B.) Router(config)# interface serial1/0
C.) Router(config)# interface serial0.1
D.) Router(config)# interface serial0/1 | | 4 |
| hello friend i have answerd more time of your question or
doute.now i am seeing towards you for help,plz send the
soln before monedya
the problem is
i have three router r1 and r2 and r3
they are conested in that maneer
thai is
r1---r2---r3---server
|
|
server
bothe server have diffrent ip
now i have to implemnt access list on the r3 router in such
a way that user from r1 can access only one server
while user from r2 can access whole servre
i ahve done it but both user of r1 and r2 uses all server
i need help
please help me this time?
i have repalsced my firwall by r3 router
so bacicaly i have to implement it on my firewall but you
tell me on cisco router please help | | 2 |
| What IP command would you use to test the entire IP stack?
A.) Stack-test
B.) Arp
C.) Telnet
D.) Ping
E.) Trace | | 1 |
| Identify the default IPX serial encapsulation?
A.) Novell-Ether
B.) SDLC
C.) SNAP
D.) HDLC | | 1 |
| Identify the command that will display the RIP routes
entering and
leaving the router?
A.) Router(config)# debug ip rip
B.) Router# debug ip rip
C.) Router>debug ip rip
D.) Router# debug rip routes | | 1 |
| Which of the following will apply IPX sap access list 1010 for
incoming traffic, assume you are at the interface configuration?
A.) ipx input-sap-filter 1010 in
B.) ipx input-sap-filter 1010
C.) ipx access-group 1010 in
D.) ipx access-list 1010 in | | 1 |
| What is the distance limitation for 100BaseT?
A. 607 ft
B. 25 Meters
C. 1,000 ft
D. 185 Meters | | 1 |
| Which of the following describe full-duplex transmission?
A.) Uses a single wire
B.) Data transmission in only both directions, but only one
way at a time
C.) Uses a point-to-point connection from the transmitter of the
transmitting station to the receiver of the receiving station
D.) Data transmission in only one direction | | 1 |
| What is the regional telco office called, where the customers
local loop terminates?
A.) Demarc
B.) DTE
C.) DCE
D.) CO
E.) CPE | | 1 |
| Sequence and acknowledgement numbers are used for?
A.) Layer transitioning
B.) Flow control
C.) Port number addressing
D.) Reliability | | 1 |
| What does -1 signify in an extended IPX access list?
A. permit this host
B. deny this host
C. permit only this subnet
D. any host or any network | | 2 |
| What does a router do with a packet that it does not have a
destination network for?
A.) Sends it to the Serial port
B.) Drops the packet
C.) Sends it back out the same interface it received it in
D.) Forwards the packet to the next hop | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
