| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Using the access-list command, 'access-list 1 deny 2.2.2.2',
what
else must be done to stop host 2.2.2.2 from sending any
traffic out of
physical interface E0,
while still allowing other traffic?
A.) In global mode, Add a line - 'access-list 1 permit
0.0.0.0 255.255.255.255'
B.) On interface E0, Add a line - 'access-group 1 in'
C.) In global mode, Add a line - 'access-list 1 permit all'
D.) On interface E0, Add a line - 'access-list 1 in'
E.) On interface E0, Add a line - 'access-list 1 out'
F.) On interface E0, Add a line - 'ip access-group 1' | | 1 |
| Identify the length of an IPX address and it's components?
A.) 80 bits, 48 bits network and 32 bits node
B.) 32 bits, 16 bits network and 16 bits node
C.) None of the above
D.) 80 bits, 32 bits network and 48 bits node | | 1 |
| Identify the components in the following command 'interface
serial0/1/1'
A.) Serial interface, port number 0, slot 1, port adapter 1
B.) Serial interface, slot 1, port number 1, port adapter 0
C.) Serial interface, slot 0, port adapter 1, port number 1 | | 2 |
| Put the following steps of encapsulation into the correct order:
1) The data is broken into segments to be organized
2) Frames are converted to 1s and 0s to be put on the wire
3) Packets are converted into frames
4) Information that users enter is converted into data
5) The segments are changed to packets to be routed
A.) 4, 1, 3, 2, 5
B.) 4, 5, 1, 3, 2
C.) 2, 3, 1, 4, 5
D.) 4, 1, 5, 3, 2 | | 1 |
| IP RIP routing is conferred on a router but not all
interfaces attach to RIP networks. What should you use to
prevent all RIP routing updates from being sent through
selecedc interfaces without using access lists?
A. passive route
B. default routes
C. passive interface
D. route update filtering | | 2 |
| Hi Anyone can share the latest ICND1 (640-822)dumps updated
at 30 september 2009. specialy to Jatendra if you have any
updated about the ICND1 exam.will be remain thankful. | | 2 |
| You are given the following address: 128.16.32.13/30.
Determine the subnet mask, address class, subnet address,
and broadcast address.
A. 255.255.255.252, B,128.16.32.12, 128.16.32.15
B. 255.255.255.252, C,128.16.32.12, 128.16.32.15
C. 255.255.255.252, B,128.16.32.15, 128.16.32.12
D. 255.255.255.248, B,128.16.32.12, 128.16.32.15 | | 1 |
| Which OSI layer performs code conversion, code formatting and
encryption?
A.) Physical
B.) Data-Link
C.) Application
D.) Transport
E.) Presentation
F.) Network | | 1 |
| Hi Jitendera, I need ur suggestion. I completed my CCNA
certification & also hving some sort of real time
experience. Now i m planning to do CCNP. Little bit
confusion is that whether it wud be better for me to go for
CCNP ya CCNA (Security). As off my goal is to reach CCIE
(Security & Switching/Routing). So tell me some solution of
my confusion yaar..!!!
Thanx & Regards
Shahin.. | | 1 |
| Identify the keystroke used to terminate the setup mode?
A.) Ctrl-K
B.) Crtl-C
C.) Ctrl-Z
D.) Crtl-End | | 1 |
| Which command will display the IPX routing table?
A.) show routes
B.) show routes ipx
C.) show routes protocol=ipx
D.) show ipx
E.) show ipx route | | 1 |
| What ISDN protocol specifies concepts, terminology, and
services?
A.) Q
B.) S
C.) I
D.) E | | 1 |
| Identify the switching method that examines the destination MAC
address as
the frame is being received then begins forwarding the frame
prior to
receiving the entire frame?
A.) Fragment-free
B.) Store and Forward
C.) Cut-through
D.) Fast forward | | 1 |
| What are hold-downs used for?
A.) To prevent regular update messages from reinstating a
route that has
come back up
B.) Information received on an interface cannot be sent back
out the
same interface
C.) To prevent regular update messages from reinstating a
route that has
gone down
D.) To hold the routing table from being sent to another router | | 1 |
| What three occurrences will reset the holddown timer after a
triggered
update?
A.) Infinity is finally defined as some max number
B.) HD Timer expires
C.) Another update is received indicating a better metric
D.) The router receives a processing task proportional to
the number of
links in the internetwork
E.) The router detects fault LSP's propagating through the
internetwork
F.) Another update is received indicating net status changed | | 1 |
| Using the TCP/IP protocol suite, a message is sent from host
A to a destination IP address on the same LAN. How does
host A determine the destination of a MAC address?
A. It uses a proxy APP
B. It uses APP requests
C. It uses PARP requests
D. It uses a router lookup table | | 1 |
| Novell NetWare has an Ethernet frame type called
Ethernet_II. What
is the matching Cisco command line keyword for this
encapsulation method?
A.) dix
B.) sap
C.) arpa
D.) gns
E.) snap
F.) novell-ether | | 1 |
| Which two statements are true? (Choose two)
A. Ethernet 802.3 utilizes a half duplex method for data
transfer
B. In a 100 MBS point to point connection a full duplex
connection can provide 400 Mbs of data transfer
C. Ethernet switches can use the full duplex mode to connect
multiple nodes on a single pod of a switch
D. Full duplex Ethernet takes advantage of UTP using one
pair for transmission and the other pair for reception | | 1 |
| Identify 2 reasons for disabling CDP?
A.) If the router is not configured for RIP
B.) Save bandwidth by eliminating overhead
C.) If the router is configured for Appletalk
D.) When connected to a non-Cisco router | | 1 |
| Which protocol resolves an IP address to a MAC address?
A.) DHCP
B.) RARP
C.) ARP
D.) NBP
E.) DNS | | 4 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
