| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Windowing is a type of?
A.) Negative acknowledgement
B.) Address resolution
C.) Layer transition mechanism
D.) Flow control | | 1 |
| What is the default routing metric used by IGRP?
A.) MTU, delay, bandwidth, reliability, and loading
B.) Count to infinity
C.) Bandwidth and delay
D.) Hop count | | 2 |
| Which command will copy the routers configuration from NVRAM
to a
Network file server?
A.) copy start tftp
B.) copy start tftp server
C.) copy tftp startup-config
D.) copy running-config tftp
E.) copy startup-config tftp | | 1 |
| Which of the following are Distance Vector protocols?
A.) IGRP
B.) RIP
C.) OSFP
D.) EIGRP | | 3 |
| Given an IPX network with redundant paths, what command will
configure load balancing?
A.) ipx load-balance
B.) ip maximum-paths 2
C.) ipx maximum-paths 2
D.) ipx load-share | | 1 |
| "arpa" is used by the Cisco IOS for which encapsulation
types?
A. Ethernet_II
B. Ethernet_802.3
C. Ethernet_802.2
D. Ethernet_SNAP | | 1 |
| PICT & JPEG are examples of what layer in the OSI seven
layer model?
A.) Transport
B.) Presentation
C.) Application
D.) Datalink
E.) Network
F.) Session | | 1 |
| Identify the command to disable CDP on an interface?
A.) Router(config-if)# no cdp enable
B.) Router(config-if)# no cdp run
C.) Router# no cdp enable
D.) Router(config-if)# no cdp | | 1 |
| To monitor ipx traffic on a network, what command would you use?
A. debug ipx transaction
B. show ipx traffic
C. show ipx events
D. display ipx traffic | | 2 |
| Which OSI layer provides best effort end to end packet delivery?
A.) Data-Link
B.) Presentation
C.) Network
D.) Transport
E.) Physical
F.) Application | Barnes-and-Noble | 2 |
| When using access lists, what does a Cisco router check first?
A. To see if the packet is routable or bridgeable
B. The destination address
C. The source address
D. The packet contents | | 1 |
| Identify the 3 guidelines for routers in the same autonomous
system?
A.) Must be configured for IGRP or RIP
B.) Interconnected
C.) Assigned the same autonomous system number
D.) Configured for the same routing protocol
E.) Must be same model of router | | 1 |
| Which of the following is a connectionless protocol at the
Transport layer?
A.) UDP
B.) ARP
C.) ICMP
D.) RARP
E.) IP
F.) FTP | | 4 |
| Which range of possible numbers do standard ipx access lists
have?
A. 100 199
B. 600 699
C. 800 899
D. 1000-1099 | | 1 |
| What command do you enter at the keyboard to begin a user mode
session?
A.) Type 'CTRL-P'
B.) Type 'login'
C.) Just press .
D.) Type 'enable'
E.) Press 'Shift + Ctrl + 6' at the same time. | | 1 |
| Identify the administrative distance and appropriate routing
protocol?
A.) RIP = 255, IGRP = 100
B.) RIP = 100, IGRP = 120
C.) RIP = 1, IGRP = 0
D.) RIP = 120, IGRP = 100 | | 3 |
| What does the IPX maximum-path command do?
A.) Allows you to disable the TTL on an IPX packet
B.) This parameter is only used in NLSP routing
C.) Sets the maximum metric that can appear in the routing table
D.) Configures round robin load sharing over multiple equal
metric paths
(parallel paths) | | 1 |
| Identify the command that displays traffic statistics on
serial0/1?
A.) display interface serial0/1
B.) show interface serial0/1
C.) show seria0/1 stats
D.) show interface serial0/1 stats | | 1 |
| What type of frame does CDP use to gather information about it's
neighbors?
A.) TCP/IP
B.) Novell-ether
C.) Subnetwork Access Protocol (SNAP)
D.) Ethernet_II | | 1 |
| Identify the command that will display the RIP routes
entering and
leaving the router?
A.) Router(config)# debug ip rip
B.) Route# debug ip rip
C.) Router>debug ip rip
D.) Router# debug rip routes | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
