| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Write an access list line which will deny
node 20.0.2.1 to anywhere on your network using
DNS via UDP. Don't worry about the other access
list lines.
| | 2 |
| What is LSA? How many types of LSA used by OSPF version 2?? | Hathway | 2 |
| The Datalink Layer is broken down into 2 layers, LLC and
MAC. The LLC
establishes media independence and what else?
A.) Provides Windowing.
B.) Provides flow control.
C.) Provides SAP's (Service Access Points).
D.) The Datalink layer does not have sublayers.
E.) Provides SAP's (Service Advertising Protocol).
F.) RIP Updates. | | 1 |
| The following commands were entered at the command prompt of a
Cisco router. What do they accomplish?
access-list 1000 deny 9e.1234.5678.1212 4
access-list 1000 permit -1
interface ethernet 0
ipx network 9e
interface ethernet 1
ipx network 4a
interface serial 0
ipx network 1
ipx output-sap-filter 1000
A. File server advertisements from server 9e.1234.5678.1212
will not be
forwarded on interface S0.
B. All other SAP services, other than file server, from any
source will
be forwarded on S0.
C. All other SAP services, other than print server, from any
source will
be forwarded on S0.
D. Print server advertisements from server 9e.1234.5678.1212
will not be
forwarded on interface S0. | | 1 |
| Identify 3 Fast Ethernet technologies?
A.) 100 Base FastEther
B.) 100 Base FX
C.) 100 Base T4
D.) 100 Base TX | | 1 |
| Identify the length of an IPX address and it's components?
A.) 80 bits, 48 bits network and 32 bits node
B.) 32 bits, 16 bits network and 16 bits node
C.) None of the above
D.) 80 bits, 32 bits network and 48 bits node | | 1 |
| Which three basic switch functions increase available
bandwidth on the networks? (Choose three)
A. loop avoidance
B. address learning
C. hop count limiting
D. broadcast filtering
E. packet forward/filtering | | 3 |
| Cisco routers use wildcard masking to identify how to check or
ignore corresponding IP address bits. What does setting a
wildcard mask
bit to 0 cause the router to do?
A. It tells the router to check the corresponding bit value.
B. It tells the router to ignore the corresponding bit value.
C. It tells the router to check its alternate routing list.
D. It tells the router to use its primary routing list. | | 1 |
| What is the command to manually enter a static route?
A.) IP route network
B.) IP route
C.) IP route < destination network>
D.) IP route | | 1 |
| Which of the following are valid Cisco encapsulation type names?
A.) arpa = IPX Ethernet
B.) novell-ether = IPX Ethernet_802.3
C.) snap = IEEE 802.2 SNAP on Ethernet, FDDI, and Token Ring
D.) novell-fddi = IPX Fddi_Raw
E.) sap = IEEE 802.2 on Ethernet, FDDI, and Token Ring
F.) hdlc = HDLC on serial interfaces | | 1 |
| What is true when creating static route?
A.) The mask parameter is optional
B.) The administrative distance is required
C.) The gateway parameter is required
D.) The administrative distance is optional | | 1 |
| What is the default IPX Ethernet encapsulation?
A.) SNAP
B.) Arpa
C.) 802.2
D.) Novell-Ether
E.) SAP | | 2 |
| Why Clock rate command is not configured on ethernet
interface of a router? | | 4 |
| How many collisions are caused by transmitting and receiving
frames simultaneously in a full-duplex Ethernet technology?
A. one
B. two
C. none
D. several | | 1 |
| What are the OSPF router rules???? | NIIT | 6 |
| Which three of the following are true statements about
connection-oriented sessions?
A.) The segments delivered are acknowledged back to the
sender upon
their reception
B.) Any segments not acknowledged the are retransmitted by
the receiver
C.) A manageable data flow is maintained in order to avoid
congestion,
overloading and loss of any data
D.) Segments are sequenced back into their proper order upon
arrival at
their destination | | 1 |
| Which OSI Reference Layer is concerned with logical addressing?
A.) Network
B.) Transport
C.) Datalink
D.) Physical
E.) Session | | 1 |
| Identify the 2 hardware components used to manage and/or
configure
a router?
A.) Auxiliary port
B.) ROM port
C.) Management port
D.) Console port | | 1 |
| As a system administrator, you want to debug igrp but are
worried that the "debug IP igrp transaction" command will
flood the console. What is the command that you should
use?
A. debug IP igrp event
B. debug IP igrp-events
C. debug IP igrp summary
D. debug IP igrp events | | 1 |
| Which of the follwing are true of standard half-duplex
Ethernet circuitry?
A. It is alternate one-way communication
B. The receive (RX) is wired directly to the transmit (TX)
of the remote station
C. The transmit (TX) is wired directly to the receive (RX)
of the remote station
D. Collisions are not possible
E. Both stations can transmit simultaneously | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
