| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What command will not display the status of to1?
A.) show int to1
B.) show to1
C.) show interface to1
D.) show interface | | 1 |
| In regards to TCP/IP, which class of address allows for the
fewest
valid Internet hosts?
A.) D
B.) E
C.) Classes are not used in TCP/IP.
D.) B
E.) C
F.) A | | 1 |
| Identify the mode reflected by the following prompt 'Router'?
A.) Setup
B.) RXBoot
C.) Boot mode
D.) Privileged exec mode | | 1 |
| Which command line option will determine what traffic is
interesting enough to establish a dialup connection?
A.) dialer map
B.) dialer string
C.) dialer in-band
D.) dialer-list
E.) dialer negotiation | | 1 |
| Identify 3 methods used to prevent routing loops?
A.) Split horizon
B.) Holddown timers
C.) Poison reverse
D.) SPF algorithm
E.) LSP's | | 1 |
| What is the IEEE specification for Spanning Tree Protocol?
A.) 802.9
B.) 803.ud
C.) 803
D.) 802.1d | | 1 |
| What does the IPX maximum-path command do?
A.) Allows you to disable the TTL on an IPX packet
B.) This parameter is only used in NLSP routing
C.) Sets the maximum metric that can appear in the routing table
D.) Configures round robin load sharing over multiple equal
metric paths
(parallel paths) | | 1 |
| Identify the 3 Internet layer IP protocols?
A.) NetBios
B.) IPX
C.) ARP
D.) IP
E.) RARP | | 1 |
| Which command sets IGRP as the routing protocol for
autonomous system 100?
A. Router(config)#igrp 100
B. Router(config)#network 100
C. Router(config)#router igrp 100
D. Router(config)#enable igrp 100 | | 1 |
| What ISDN protocol specifies concepts, terminology, and
services?
A.) Q
B.) S
C.) I
D.) E | | 1 |
| Which of the following are valid WAN terms?
A.) DTE
B.) DCE
C.) Demarc
D.) CPE | | 1 |
| What is a key use of a device hardware address?
A. to obtain a vendor code / serial number from the user
B. to transmit a frame from one Interface to another Interface
C. to transmit a packet from one local device to another
local device
D. to transmit data from one local device to a remote device
across the internet
E. to contain logical information about the device to use
for end-to-end transmission | | 1 |
| What is the correct command line syntax for configuring a
port on
a 7000 or 7500 series Cisco router with a VIP card?
A.) port
B.) port adapter/port
C.) You can't put a VIP card in a 7000 or 7500 router.
D.) slot/port-adapter/port
E.) slot/port
F.) slot | | 1 |
| Identify the command to view the configuration-register value?
A.) show register
B.) display config-register
C.) show config
D.) show version | | 1 |
| Identify the command to configure the configuration-register?
A.) Router# config-register 0x2102
B.) Router(config)# config-register 0x2102
C.) Router(config-reg)# 0x2102
D.) Router> config-register 0x2102 | | 1 |
| Which NetWare protocol works on layer 3--network layer--of
the OSI model?
A. IPX
B. NCP
C. SPX
D. NetBIOS | | 1 |
| Inverse ARP serves what purpose?
A.) Method for a local router to introduce itself to the
remote end of
the connection
B.) Broadcast a routing table update
C.) Identify MAC addresses if the IP address is known
D.) Sent every 10 seconds used to verify the Frame Switch is
still active | | 1 |
| Which of the following are logged when IP access list logging is
enabled?
A.) source address
B.) protocol
C.) source port
D.) destination address
E.) access list number
F.) destination port | | 1 |
| Which show command should you use to view Frame Relay Local
Management Interface (LMI) Frame statistics?
A. show lmi
B. show ip route
C. show interface
D. show statistics
E. show frame-relay lmi | | 1 |
| Which layer allows multiple Ethernet devices to uniquely
identify
one another on the Datalink layer?
A.) Transport
B.) Session
C.) Network
D.) Datalink - MAC Sublayer
E.) Datalink - LLC Sublayer | | 3 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
