| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the 2 commands that will display the status and
information about interface E0 only?
A.) show interface ethernet E0
B.) show interface E0
C.) show E0
D.) show int E0
E.) show interface | | 1 |
| Identify the access-list range for an extended IP access-list?
A.) 800 - 899
B.) 1 - 99
C.) 1000 - 1099
D.) 100 - 199 | | 4 |
| You want to segment a network. The network is running SNA and
Netbios. Which device should NOT be used to segment the network?
A.) A store and forward switch.
B.) A router.
C.) A Catalyst 5000.
D.) A cut-through switch.
E.) A bridge. | | 1 |
| Request any body to explain the parameters of Ipsec vpn
tunnel while creating a tunnel in Cisco ASA. | HCL | 3 |
| In version 11.2 of the IOS, a Cisco router configured for
frame-relay can automatically detect the LMI type. What is
this known as?
A.) Psychic
B.) ESP
C.) Inverse ARP
D.) Hello
E.) Reverse ARP
F.) Autosense | | 1 |
| Given the command 'cl?', what will it display?
A.) Syntax of the 'clock' command
B.) Syntax of the 'clear' command
C.) All commands that begin with 'cl'
D.) All commands that begin with 'c' | | 2 |
| When you mistakenly type the wrong command
at the Router# prompt the router does a
DNS lookup which takes about 20 seconds.
Which command can you enter to prevent the
router doing this in future? | | 3 |
| Identify the command to run 'setup'?
A.) Router(config)#setup
B.) Router?setup
C.) Router#setup
D.) Router>setup | Karrox | 1 |
| What would be the proper wildcard mask to permit all odd
numbered hosts on the 10.48.0.0/12 network?
access-list 1 permit 10.48.0.0 0.15.255.255
access-list 1 permit 10.48.0.1 0.15.255.254
access-list 1 permit 10.48.0.0 0.15.255.1
access-list 1 permit 10.48.0.0 0.0.0.254
access-list 1 permit 10.48.0.0 0.0.0.255
| | 5 |
| Identify the command to configure the router to boot from an IOS
located on a TFTP server?
A.) boot system tftp IOS.exe 172.16.5.1
B.) boot system tftp 172.16.5.1 IOS.exe
C.) boot system flash tftp 172.16.5.1
D.) boot system IOS.exe 172.16.5.1 | | 1 |
| Which command line statement determines the number of seconds a
dialup connection can wait without any traffic before the
router hangs up?
A.) dialler max-time
B.) dialler timeout
C.) dialer idle-timeout
D.) dialer hang-up
E.) disconnect-timer | | 2 |
| CO is an acronym for which of the following?
A.) Central Office
B.) Capital Office
C.) Central Operator
D.) Company Office | | 1 |
| raid can be used in?
1 NT
2 Netware
3 all of above
mine answer -NT | | 2 |
| You have just issued the erase startup-config Command and
reloaded your router. In which mode will your router be
when you react?
A. setup
B. startup
C. user EXEC
D. userd privileged
E. global configuration | | 2 |
| what is the difference between
1 router and switch
2 router and hub
3 hub and switch
4 bridge and switch
| Hathway | 1 |
| let there are three switch and there are 3 ree valn craed
on each switch that is vlan 2 on first switch valn 3 on 2nd
switch and vlan 4 is cretaed on switch 3
i have implemnted intervlan routin through ciso switchses.
the router is conected through its fa0/1 port by one switch
and and the two switch are trunked with each other
now question is that we want to comuniacte betwwen vlan but
does alse want that only vlan 2 is allow to access internet
(ISP)which is conected through s0 interface of router.and
no any vlan can access that internet.what should be
solution. | | 1 |
| The Cisco IOS is stored in:
A.) ROM
B.) CD
C.) Flash
D.) NVRAM | | 3 |
| Identify the components in the following command 'interface
serial0/1/1'
A.) Serial interface, port number 0, slot 1, port adapter 1
B.) Serial interface, slot 1, port number 1, port adapter 0
C.) Serial interface, slot 0, port adapter 1, port number 1 | | 2 |
| Which switching technology can reduce the size of a
broadcast domain?
A.) Cut-Through
B.) Store-and-Forward
C.) Spanning Tree Protocol
D.) RARP
E.) ARP
F.) VLAN | | 1 |
| Which is true regarding store-and-forward switching method?
A.) Latency varies depending on frame-length
B.) Latency is constant
C.) It is default for all Cisco switches
D.) It only reads the destination hardware address before
forwarding the
frame | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
