| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What is the result of using a hierarchical addressing framework?
A. increased availability of addresses
B. decreased distance between routers
C. increased router memory requirements
D. no need to maintain routing information | | 1 |
| To monitor ipx traffic on a network, what command would you use?
A. debug ipx transaction
B. show ipx traffic
C. show ipx events
D. display ipx traffic | | 2 |
| as we know that isdn bri port come with either a u
interface or some thing s/t interface what is the
diffrenmce between them | HCL | 1 |
| Which of the following are examples of the Transport Layer?
A.) SQL
B.) UDP
C.) IP
D.) LLC
E.) ARP | | 1 |
| Identify the mode reflected by the following prompt 'Router'?
A.) Setup
B.) RXBoot
C.) Boot mode
D.) Privileged exec mode | | 1 |
| How we ping ICMP a NIC with a correct IP address but with
wrong MAC address
Do all NIC's can run inpromiscuous mode | Cisco | 3 |
| In Cisco IOS software which command displays the backup
configuration?
A. show flahh
B. show version
C. show tftp-config
D. show backup-config
E. show startup-config | | 1 |
| What does 'P' mean when running a Trace?
A.) Good route
B.) Protocol unreachable
C.) Source Quench
D.) Destination unreachable | | 2 |
| What command will not display the status of to1?
A.) show int to1
B.) show to1
C.) show interface to1
D.) show interface | | 1 |
| Identify the command to configure DLCI 100 on an interface e0?
A.) Router(config)# frame-relay local-dlci 100
B.) Router(config)# frame-relay local-dlci 100 int e0
C.) Router(config-if)# frame-relay local-dlci 100
D.) Router(config-if)# frame-relay local-dlci 100 int e0 | | 1 |
| When you use the Cisco IOS command show configuration on a
router which part of the output shows the specific conferred
IP addresses and shored masks?
A. the IP host table
B. the interfaces output
C. each section of the output
D. the global configuration statements
E. the section under the autonomous system number | | 1 |
| Identify the effect of Ctrl-Z?
A.) Exits back to privileged exec mode
B.) Disconnect from the router
C.) Abort the ping operation
D.) Exits privileged exec mode | | 2 |
| Which of the following are Distant Vector protocols?
A.) IGRP
B.) RIP
C.) OSFP
D.) EIGRP | | 1 |
| Which of the following protocols are used to get an IP address
from a known MAC address?
A.) BootP
B.) TCP
C.) IP
D.) ARP
E.) RARP
F.) ICMP | | 1 |
| Hi Guys i hv one confusion. Need u peoples help.
In EIGRP, maximum hop count is up to 255. By default only
100. Now question is -
a) Suppose i hv a network consist of 115 routers & EIGRP
routing protocol is configured. By default hop count is 100,
so is there any manual configuration necessary for hop count
ya router will automatically detect the hop count & will
update the hop count accordingly..?????
b) In EIGRP, Bandwidth & Delay is used to calculate metric.
For this Metric weight is set to K1(Bandwidth)=1,
K2(Delay)=0, K3(Reliability)=1, K4(Load)=0, K5(MTU)=0
Now i want, Bandwidth & Load is used to calculate metric.
For that wat i hv to configure & wat wub the metric weights.
Cud anyone explain it plzzzz..!!!! | | 5 |
| Choose the following that are benefits to segmenting with
router:
A.) Flow Control
B.) Manageability
C.) Multiple Active Paths
D.) Explicit packet lifetime control | | 1 |
| Based upon the 1st octet rule identify the range for a Class A
address?
A.) 1 - 126
B.) 192 - 223
C.) 128 - 191
D.) 1 - 191 | | 1 |
| Identify the number range for IPX SAP filters?
A.) 900 - 999
B.) 1000 - 1099
C.) 800 -899
D.) 100 - 199 | | 1 |
| What does the Spanning Tree Algorithm (STA) do?
A.) Restore lost frames
B.) Builds routing tables for routing through an internetwork
C.) Forward packets through a switch
D.) STA is implemented by STP to prevent loops | | 1 |
| Which OSI layer handles physical address, network topology?
A.) Presentation
B.) Physical
C.) Transport
D.) Application
E.) Data-Link
F.) Network | | 1 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
