| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which device listed below provides clocking for the line?
A.) DCE
B.) CPE
C.) CO
D.) DTE
E.) Demarc | | 1 |
| The Cisco Catalyst 5000 switch supports full duplex. How
would you
enable it on the second port of the card in slot 1?
A.) router(config-if)# duplex full
B.) router(config)# duplex full
C.) router(config-if)# set port duplex
D.) router(config)#port duplex = full
E.) router(config-if)# set port 1/2 full | | 1 |
| Which two statements about a bridge are true? (Choose two)
A. A bridge floods multicasts
B. A bridge floods broadcasts
C. A bridge does not flood multicasts
D. A bridge does not flood broadcasts | | 1 |
| You need to come up with a TCP/IP addressing scheme for your
company. Which two factors must you consider when you define
the subnet
mask for the network?
A.) The location of DHCP servers
B.) The volume of traffic on each subnet
C.) The number of subnets on the network
D.) The location of the default gateway
E.) The number of host IDs on each subnet | | 1 |
| What is the command to allow you to type Tokyo instead of the IP
address 172.16.30.1 to access a router named Tokyo?
A.) config t, ip host Tokyo 172.16.30.1
B.) config t, ip hostname Tokyo 172.16.30.1
C.) config t, hostname Tokyo 172.16.30.1
D.) config t, ip hostname 172.16.30.1 Tokyo | | 1 |
| What IP command would you use to test the entire IP stack?
A.) Stack-test
B.) Arp
C.) Telnet
D.) Ping
E.) Trace | | 1 |
| Which addresses are valid host addresses?
A. 201.222.5.17
B. 201.222.5.18
C. 201.222.5.16
D. 201.222.5.19
E. 201.222.5.31 | | 2 |
| Identify the 2 commands to copy a configuration from a TFTP
server
to RAM?
A.) configure network
B.) configure overwrite
C.) copy backup-config running-config
D.) copy tftp running-config | | 1 |
| Which command should you use to confound a router so that it
can become a TFTP server host for a router system image that
is run in a Flash?
A. copy flash tftp
B. config tftp server
C. write, network -router name-
D. tftp-server system -file name-
E. setup server tftp -system name- | | 1 |
| What is VLSM? how to Calculate VLSM? where it is use and
why? | | 4 |
| Identify the command to configure a description on an interface?
A.) Router> description Finance department
B.) Router(config)# description Finance department
C.) Router(config-if)# description Finance department
D.) Router# description Finance department | | 1 |
| Identify the type of routing protocol that maintains a
topological
database of the network?
A.) Topological state
B.) Shortest Path First
C.) Link state
D.) Distance vector | | 1 |
| Identify the following components of the IPX address
2e.0000.0065.ed43
A.) Not a valid IPX address
B.) Network = 2e, Subnet = 0000, Node = 0065.ed43
C.) Network = 2e.0000, Node = 0065.ed43
D.) Network = 2e, Node = 0000.0065.ed43 | | 1 |
| Which layer of the 7 layer model provides services to the
Application layer over the Session layer connection?
A.) Transport
B.) Application
C.) Session
D.) Network
E.) Datalink
F.) Presentation | | 1 |
| Which three basic switch functions increase available
bandwidth on the networks? (Choose three)
A. loop avoidance
B. address learning
C. hop count limiting
D. broadcast filtering
E. packet forward/filtering
F. broadcast packet hop count learning/forward/filtering | | 1 |
| what is the purpose of multicast packets? | | 1 |
| The Network layer works with which of the following:
A.) Globules
B.) Bits
C.) Packets
D.) Segments
E.) Frames | | 2 |
| CSMA/CD stand for which of the following?
A.) Carrier Sense, Multiple Access with Collision Detection
B.) Collision Sense, Multiple Access with Collision Detection
C.) Collision Sense, Multiple Access with Carrier Detection
D.) Carrier Sense, MAC address with Collision Detection | | 1 |
| Hi, All
I am configuring EIGRP in Packet tracer, after configuring
all the things it is not working but in one condition it is
working fine if i am putting all my router and network
withing one network subnets e.g. 172.16.0.0 or 10.0.0.0 but
whenever i am puting different network subnets e.g. in one
network it is RA(config-if)#=ip address 10.0.0.1, and in
fa0/0= 192.168.1.10 and in RB(config-if)#10.0.0.2 (s1/0) and
in S1/1 11.0.0.1 and in fa 0/0 192.168.100.1 ,where as in
third router RC(config-if)#=ip address 11.0.0.2 and in fa
0/0 172.16.1.10 and after configuring all this serial is
showing up and protocol showing up but eigrp process not
taking place after adding eigrp configuration, i tried with
"no auto-summary" command but not working.. Suggest me where
i missing something? can mail me at : gtech.innovator@gmail.com | | 18 |
| Identify the command to determine if CDP is enabled?
A.) show enable cdp
B.) show cdp enabled
C.) show cdp run
D.) show cdp | | 1 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
