| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| MIDI and MPEG are examples of what layer of the OSI seven layer
model?
A.) Session
B.) Network
C.) Datalink
D.) Transport
E.) Application
F.) Presentation | | 1 |
| Station A is transmitting data to station B, and expects an
acknowledgment
after every 400 bytes. After transmitting data for a while,
the two
stations determine the line is reliable and change to
expecting and
acknowledgement every 600 bytes.
This is an example of (pick the best answer only):
A.) BECN
B.) Sliding Windows
C.) Poison Reverse
D.) Countdown timers
E.) Split Horizon
F.) Count to infinity | | 1 |
| Which command would show all Ethernet interfaces with IPX
configured on them?
A.) show interface ipx ethernet
B.) show ipx interface
C.) show ipx interface ethernet
D.) show ipx
E.) show version
F.) show run | | 1 |
| The Cisco IOS is stored in:
A.) ROM
B.) CD
C.) Flash
D.) NVRAM | | 3 |
| Which layer of the 7 layer model provides services to the
Application layer over the Session layer connection?
A.) Transport
B.) Application
C.) Session
D.) Network
E.) Datalink
F.) Presentation | | 1 |
| Which statement about the Point to Point Protocol (PPP) is true?
A. PPP supports TCP/IP but not Novell IPX
B. PPP is being phased out of existence by the Serial Line
Internet Protocol (SLIP)
C. PPP providces router to router and host to network
connections over both synchronous and asynchronous circuits
D. PPP is an ITU T and ANSI standard that defines the
process for sending data over a packet switched data network
(PSDN) | | 1 |
| Most routing protocols recognize that it is never useful to send
information about a route back out the direction from which
the original
packet came. This is an example of which routing technology?
A.) Split Horizon
B.) LMI
C.) Triggered Updates
D.) Poison Reverse
E.) SYN, ACK
F.) DLCI | | 1 |
| You are a system administrator on a NetWare network, you are
running NetWare 4.11 and you cannot communicate with your
router. What is the likely problem?
A. NetWare 4.11 defaults to 802.2 encapsulation.
B. NetWare 4.11 defaults to 802.3 encapsulation
C. Cisco routers only work with NetWare 3.11.
D. NetWare 3.11 defaults to 802.2 encapsulation. | | 1 |
| On a network design project you determine that a new testing
application requires multiple hosts. These hosts must be
capable of sharing data between each host and an enterprise
server at 10 Mobs bandwidth. Other divisions in the company
use applications that require less than 2 Mobs bandwidth of
the enterprise server. What is your most economical
recommendation?
A. That existing 10BaseT hubs be replaced with 1 00BaseT
hubs to improve overall performance
B. That a router can separate the testing application from
the rest of the network, thus allowing the testing
application more bandwidth.
C. That a switch be installed, so that the enterprise server
can be provided a 100 Mobs pod and each of the testing
application hosts can be given dedicated 10 Mobs pods]
D. That a bridge be placed between the enterprise server and
all other users with the exception of the testing application | | 1 |
| Which of the following are Transport layer protocols?
A.) UDP
B.) TCP
C.) NBP
D.) IP
E.) SPX | | 1 |
| what is native vlan
any one explain
sooraj | | 2 |
| Identify the command to reload the router?
A.) Router(config)# reload
B.) Router# reset
C.) Router# reload
D.) Router> reload | | 1 |
| At which layer of the OSI model does the ping command operate?
A. session
B. network
C. transport
D. maintenance | jetking | 6 |
| in the ospf area network dr and bdr selection procedure occur
let there are 4 router in that n/w r1 have the higher priority
then r2 and r2 have higher priority then r3 and so on
like that
r1>r2>r3>r4
now as we know that selection of dr and bdr based upon the
router priority so in this case r1 will be dr and r2 will be
bdr
now my question is that if i am going to implement 5th
router which have greater priority then r1 then will it become dr atomically
remember that i am not going change my 5 or 1st router property
answer that one please | | 2 |
| What is the command to manually enter a static route?
A.) IP route network
B.) IP route
C.) IP route < destination network>
D.) IP route | | 4 |
| Identify 3 characteristics of ISDN?
A.) Transports voice and data
B.) Transports voice only
C.) Support both BRI and PRI
D.) Runs over existing phone lines
E.) Same as X.25 | | 1 |
| friends i have 3ree prob which is asked in ibm india in
technical round
1 what is ftp(this was easy i had answered)
2 why we use ftp(i think it is a tough one)
3 how can we enable ftp in the widows xp.
friend i need these question answer as soon as possible
if it is possible to reply within the eveing then i always
obeyliged to you
i am espacily looking towards the jitendera sinha who make
most of the valuable answer
loking toward you
nidhi mall | IBM | 3 |
| b Which protocol for PPP LCP (Link Control Protocol) performs a
challenge handshake?
A. CHAP
B. PAP
C. UDP
D. IPX | | 1 |
| Which three functions are supported by connection oriented
servkps? (Choose three)
A. connection parameters are synchronized
B. any loss or duplication of packets can be corrected
C. the data packet is independently routed and the service
does not guarantee the packet will be processed in order
D. a data communication path is established between a
requesting entity and the peer device on the remote end system | | 1 |
| Given the global configuration commands:
'banner motd #'
'Hello #'
When would the message be displayed?
A.) The message of the day banner shows up before login.
B.) The message of the day banner shows up during logoff.
C.) These commands are not the right syntax for MOTD.
D.) Message of the day banners are displayed upon entering
global config
mode.
E.) Message of the day banners are not possible.
F.) The message of the day would be, 'Hello #' | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
