| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the hardware component used to store buffers, tables,
running-configuration etc?
A.) NVRAM
B.) ROM
C.) RAM
D.) Flash | | 3 |
| What does -1 mean in an extended IPX access-list?
A.) Any IP address
B.) Deny all
C.) Deny host
D.) Any host or any network | | 1 |
| What is the maximum hop count for Link-State protocols?
A.) 15
B.) there is no hop count limit
C.) 256
D.) 16 | | 1 |
| What is the default LMI type?
A.) Cisco
B.) ANSI
C.) IETF
D.) Q933a | | 2 |
| What do the following commands accomplish?
access-list 1 permit 172.16.0.0 0.0.255.255
interface ethernet 0
IP access-group 1 out
interface ethernet 1
IP access-group 1 out
A. Only traffic from the source network 172.16.0.0 will be
blocked.
B. Only traffic from the source network 172.16.0.0 will be
forwarded.
Non-172.16.0.0 network traffic is blocked.
C. Non-172.16.0.0 traffic will be forwarded.
D. All traffic will be forwarded. | | 1 |
| Which Cisco IOS command should you use to display the Novell
IPX address assignments on a router?
A. show ipx addresses
B. show ipx interface
C. show me the money
D. ipx, network (number)
E. display ipx addresses
F. show ipx routing details | | 1 |
| What does the term Base refer to in 100BaseT
A. cabling type
B. singnal type
C. 100 mode type
D. spectrum used
E. speed category | | 2 |
| Dear Mr.Shahin thank you very much for your advise i realy
thanks full to you.
Best of luck | | 2 |
| WHAT IS SERIAL TRANSMISSIONS,PARALLELL TRANSMISSION | ASD-Lab | 2 |
| Which of the following is used to manage and monitor the
network?
A.) SNMP
B.) HTTP
C.) IP
D.) FTP | | 1 |
| If you are running Token Ring with Novell IPX routing, which
encapsulation
should you use?
A.) SAP
B.) SNAP
C.) 802.5
D.) 802.2 | | 1 |
| Hi, All
I am configuring EIGRP in Packet tracer, after configuring
all the things it is not working but in one condition it is
working fine if i am putting all my router and network
withing one network subnets e.g. 172.16.0.0 or 10.0.0.0 but
whenever i am puting different network subnets e.g. in one
network it is RA(config-if)#=ip address 10.0.0.1, and in
fa0/0= 192.168.1.10 and in RB(config-if)#10.0.0.2 (s1/0) and
in S1/1 11.0.0.1 and in fa 0/0 192.168.100.1 ,where as in
third router RC(config-if)#=ip address 11.0.0.2 and in fa
0/0 172.16.1.10 and after configuring all this serial is
showing up and protocol showing up but eigrp process not
taking place after adding eigrp configuration, i tried with
"no auto-summary" command but not working.. Suggest me where
i missing something? can mail me at : gtech.innovator@gmail.com | | 18 |
| Identify the type of routing protocol that exchanges entire
routing tables at regular intervals?
A.) Link state
B.) Interior gateway protocols
C.) Appletalk routing
D.) Distance vector | | 1 |
| Which Distance Vector characteristic can help to speed up
convergence?
A.) Triggered Updates.
B.) Split Horizon.
C.) Poison Reverse.
D.) Hold Down timers.
E.) Inverse ARP. | | 1 |
| You are given the following address: 15.16.193.6/21.
Determine the subnet mask, address class, subnet address,
and broadcast address.
A. 255.255.248.0, A, 15.16.192.0, 15.16.199.255
B. 255.255.248.0, B, 15.16.192.0, 15.16.199.255
C. 255.255.248.0, A, 15.16.199.255, 14.15.192.0
D. 255.255.242.0, A, 15.16.192.0, 15.16.199.255 | | 1 |
| Which configuration mode and command combination sets the
bandwidth metric of a Frame Relay connection?
A. router(config)# clock rate 56
B. router(config)# bandwidth 56
C. router(config)# bandwidth 56000
D. router(config)# clock rate 56000 | | 2 |
| What does the User Datagram Protocol (UDP) provide?
A.) Connectionless datagram service.
B.) FECN & BECN
C.) Flow control and error checking.
D.) Name resolution.
E.) Path discovery. | | 1 |
| Which of the following statements are true?
A.) Store and forward switching creates variable latency
through the switch
B.) Cut through switching creates variables latency through
the switch
C.) Cut through switching works at wire speed
D.) Store and forward switching works at wire speed | | 1 |
| In the command "router igrp 109" what does 109 signify?
A. an autonomous system
B. any network number which the router is attached to
C. the allowable length of the routing table
D. the network socket number | | 1 |
| Which layer is responsible for putting 1s and 0s into a logical
group?
A.) Session
B.) Application
C.) Transport
D.) Data Link
E.) Physical
F.) Network | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
