| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which statement about half duplex Ethernet operations is true?
A. With half duplex transmission frames feed into a single
cable in one direction at a time.
B. Half duplex transmission between stations is achieved by
using point to point Ethernet and Fast Ethernet connections
C. Half duplex transmission between stations is achieved by
using point to munificent Ethernet and Fast Ethernet connections
D. Half duplex Ethernet technology provides a transmit
circuit connection wired directly to the receiver circuit at
the other end of the connection | | 5 |
| how many pass word you can configure on cisco 2500 router | HCL | 2 |
| what is diffrence between circit switching and packet
switching | Volvo | 1 |
| Can anyone explain in details the STP port state????? | | 2 |
| What is the default size of a standard ping on a Cisco router?
* A: 100 bytes
* B: 32 bytes
* C: 10 bytes
* D: 16 bytes
| CMS | 2 |
| Which layer is responsible for negotiating data transfer syntax?
A.) Network
B.) Session
C.) Application
D.) Transport
E.) Presentation | | 2 |
| Which layer is responsible for determining if sufficient
resources
for the intended communication exists?
A.) Application
B.) Network
C.) Session
D.) Presentation
E.) Transport | | 1 |
| In regards to TCP/IP, which class of address allows for the
fewest
valid Internet hosts?
A.) D
B.) E
C.) Classes are not used in TCP/IP.
D.) B
E.) C
F.) A | | 1 |
| What should be the first command to create an access-list that
prevents all users on subnetwork 10.10.128.0, using subnet mask
255.255.192.0, from being able to telnet anywhere?
A.) access-list 101 deny tcp 10.10.128.0 0.0.63.255 any eq
telnet
B.) access-list 101 deny tcp 10.10.128.0 255.255.0.0 any eq
telnet
C.) access-list 101 deny tcp 10.10.128.0 255.255.192.0 any
eq telnet
D.) access-list 101 deny tcp 10.10.128.0 0.0.192.255 any eq
telnet
E.) access-list 101 deny tcp 10.10.128.0 0.0.128.255 any eq
telnet
F.) access-list 101 deny tcp 10.10.128.0 0.0.127.255 any eq
telnet | | 1 |
| Of the following switching types, which one has the lowest
latency?
A.) Cut-through
B.) Fragment Free
C.) None
D.) Store-and-forward | | 3 |
| Which of the following are examples of the Session Layer?
A.) IP
B.) Netbios Names
C.) NFS
D.) Token Ring
E.) SQL
F.) RPC | | 2 |
| Identify the correct IGRP configuration?
A.) Router# router igrp 100
Router# network 10.0.0.0
B.) Router(config)# router igrp 100
Router(config-router)# network 10.0.0.0
C.) Router(config)# router igrp
Router(config-router)# network 10.0.0.0 | | 1 |
| Which of the following is a layer 2 device?
A.) Switch
B.) Router
C.) Repeater
D.) Hub | | 3 |
| After the command -- router igrp 200 -- what command would
enable
IGRP on the router for interface E0, with an address of
157.89.4.4 and a
mask of 255.255.255.0 ?
A.) network 157.89.4.0 255.255.255.1
B.) network 157.89.0.0
C.) router igrp *
D.) router igrp 157.89.0.1
E.) router igrp int e1
F.) router igrp 157.89.4.1 | | 2 |
| CO is an acronym for which of the following?
A.) Central Office
B.) Capital Office
C.) Central Operator
D.) Company Office | | 1 |
| Describe End to End network services: (Choose all that apply)
A.) Best Route selection
B.) Accomplished Segment by Segment, each segment is autonomous
C.) Flow Control & Data Integrity
D.) Best efforts packet delivery | | 1 |
| What is a benefit of a virtual LAN (VLAN)?
A. It increases the number of broadcast domains
B. It decreases the number of broadcast domains
C. It increases the numberr of collision domains
D. It decreases the number of collision domains
E. Since it is a vitual Interface it never shuts down | | 3 |
| Identify the command that configures the bandwidth to 56K?
A.) Router(config-if)# bandwidth 56000
B.) Router(config-if)# bandwidth 56k
C.) Router(config)# bandwidth 56
D.) Router(config-if)# bandwidth 56 | | 1 |
| Hi Jitendera, I continuously read your answers which is
more knowlegable than books...
Q.I am facing some problems in subnetting.can you plzz
explain the subnetting process.. will be remain thankful | | 3 |
| If a router uses dynamic routing, how does it learn the
route to remote networks?
The router uses a DHCP request to obtain remote network
numbers.
The router uses a routing protocol to exchange routing
info. with other routers.
The router uses DNS request packets to obtain remote
network numbers.
The Network Administrator manually configures the remote
networks.
| | 1 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
