| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which router command allows you to determine if an IP access
list is enabled on a particular interface?
A. Router# show ip interface
B. Router> show access-list
C. Router# show ip access-list
D. Router> show interface ip access-list
E. Route 1 P.O. box 198 | | 2 |
| Identify 3 ways in which a router can be configured?
A.) TFTP
B.) Nvram
C.) ROM
D.) Console
E.) Trace | | 1 |
| Which information must a router know in order to perform
proper and pungent routing?
A. destination application of an incoming packet
B. number of other packets in a single flow of data
C. destination network address of an incoming packet
D. number of routers that also know a path to the destination | | 1 |
| Which IP host address range is allowable given an IP address
of 172.37.2.56 and 12 bits of subnetting
A. 172.37.2.48 to 172.37.2.63
B. 172.37.2.48 to 172.37.2.62
C. 172.37.2.49 to 172.37.2.62
D. 172.37.2.49 to 172.37.2.63
E. 172.37.2.55 to 172.37.2.126 | | 1 |
| What is the command to allow you to type Tokyo instead of the IP
address 172.16.30.1 to access a router named Tokyo?
A.) config t, ip host Tokyo 172.16.30.1
B.) config t, ip hostname Tokyo 172.16.30.1
C.) config t, hostname Tokyo 172.16.30.1
D.) config t, ip hostname 172.16.30.1 Tokyo | | 1 |
| Using the access-list command, 'access-list 1 deny 2.2.2.2',
what
else must be done to stop host 2.2.2.2 from sending any
traffic out of
physical interface E0,
while still allowing other traffic?
A.) In global mode, Add a line - 'access-list 1 permit
0.0.0.0 255.255.255.255'
B.) On interface E0, Add a line - 'access-group 1 in'
C.) In global mode, Add a line - 'access-list 1 permit all'
D.) On interface E0, Add a line - 'access-list 1 in'
E.) On interface E0, Add a line - 'access-list 1 out'
F.) On interface E0, Add a line - 'ip access-group 1' | | 1 |
| What does the "IPX maximum-paths 2" command accomplish?
A. It enables load sharing on 2 paths if the paths are equal
metric paths.
B. It sets up routing to go to network 2.
C. It is the default for Cisco IPX load sharing.
D. It enables load sharing on 2 paths if the paths are
unequal metric paths. | | 2 |
| Which statement is true regarding Administrative distance?
A.) It is a metric
B.) Number of hops between two routers
C.) Trustworthiness of the routing information
D.) RIP Administrative distance is 100 | | 1 |
| Assuming no subnetting, which two pieces of information can
be derived from the IP address 144.132.25.10? (Choose two)
A. It is a Class C address
B. It is a Class B address
C. The network address is 144.0.0.0
D. The network address is 144.132.25.0
E. The host spoon of the address is 25.10 | | 2 |
| Identify 3 characteristics of ISDN?
A.) Transports voice and data
B.) Transports voice only
C.) Support both BRI and PRI
D.) Runs over existing phone lines
E.) Same as X.25 | | 1 |
| Identify the command that configures serial0 for PPP
encapsulation?
A.) Router(config)# encapsulation ppp
B.) Router(config-if)# encapsulation serial ppp
C.) Router(config-if)# encapsulation ppp
D.) Router# encapsulation ppp | | 1 |
| Which configuration task must you complete if a remote Frame
Relay router does NOT support Inverse APP?
A.configure static maps
B.define an IP address locally
C.disable DHCP on the Frame Relay router
D.configure a static route to the remote network | | 1 |
| Which two commands allow you to verify address configuration
in your unternetword? (Choose two)
A. ping
B. trace
C. verify
D. test ip
E. Echo ip
F. config ip | | 2 |
| What is the protocol and what is the second part of the
following network address? 172.16.0.254 mask - 255.255.0.0
A. IPX MAC address
B. IP Class C directed broadcast
C. Private IP address node number
D. Public IP directed broadcast
E. Private IP directed broadcast | | 1 |
| Which two steps are required to confound and apply standard
access lists on an interface? (Choose two)
A. define an access list number and its parameters
B. enable an interface to become part of the access list group
C. define the number of access lists to be supported on an
interface
D. copy the access list definition to each interface that
will support it | | 2 |
| Identify the 3 kinds of routes IGRP advertises?
A.) Interior
B.) Dynamic
C.) System
D.) Exterior | | 1 |
| Identify the command to display the IP routing table?
A.) show route
B.) show ip route
C.) show ip table route
D.) show ipx route | | 1 |
| Which three pieces of CDP information about neighbours
routers are displayed on your console terminal? (Choose three)
A. neighbours router a host name
B. the neighbours router a hardware platform
C. up to one address for each protocol supported
D. up to two addresses for each protocol supported | | 1 |
| Which two types of route table entries are used by a Layer 3
router to determine the appropriate path to destination?
(Choose two)
A. static route entry
B. default route entry
C. Dynamic route entry
D. temporary route entry
E. permanent route entry | | 1 |
| what is the diffination of bandwidth. | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
