| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What is the syntax to add a banner to the Cisco router?
A.) motd banner #
B.) banner
C.) banner motd #
D.) banner # | | 1 |
| router | Infotech | 1 |
| UDP works at which layer of the DOD model?
A.) Internet
B.) Host-to-Host
C.) Transport
D.) Data Link | | 1 |
| Select the fields for the Cisco HDLC protocol:
A. Flag, Address, Control
B. Flag, Address, Control, Protocol, LCP (Code, Identifier,
Length,
Data), FCS, Flag
C. Flag, Address, Control, Data, FCS, Flag
D. Flag, Address, Control, Proprietary, Data, FCS, Flag | | 1 |
| Which OSI Reference Layer is concerned with path determination?
A.) Datalink
B.) Physical
C.) Network
D.) Transport
E.) Session | | 2 |
| Given the following IP address from the Class C address
range 192.168.21.12. Your network plan needs addresses for
28 small prkps Each office uses its own shored. The
network design specifies that you confound for five bits of
subnetting. When you confound for this in Cisco IOS
software which shored mask should you use?
A. 255.255.0.28
B. 255.255.255.0
C. 255.255.255.28
D. 255.255.255.248
E. 255.255.255.252 | | 1 |
| In which two modes can the ICMP ping command be used?
(Choose two)
A. user
B. privileged
C. global configuration
D. interface configuration | | 1 |
| Which NetWare protocol provides link-state routing?
A. NLSP
B. RIP
C. SAP
D. NCP | | 1 |
| Which of the following describe SMTP?
A.) Used for downloading files to the router.
B.) Used for sending e-mail.
C.) Uses TCP.
D.) Uses UDP.
E.) Uses port 25.
F.) Used for managing IP devices. | | 1 |
| An ISDN BRI circuit can be described as which of the following?
A.) 3B channels
B.) 2-64Kbps B channels and 1-16Kbps D channel
C.) none of the above
D.) 2-64Kbps B channels and 1-16Kbps C channel | | 1 |
| Identify the 2 commands that display the clock rate
configured on
the serial0 interface?
A.) show serial0
B.) show interface serial0
C.) Show clock rate serial 0
D.) show controllers serial 0
E.) show running-config | | 1 |
| Which statement is true?
A. While bridges are used to segment networks, they will not
isolate broadcast or multicast packets.
B. A bridge looks at every packet within its network segment
and works like a hub re-broadcasting the packet if the
destination is within its network segment.
C. A bridge maintains a table of the IP addresses of the
hosts within its network segment and forwards the packet
directly to the destination based upon the IP address.
D. A bridge resets the hop count by keeping all packets
within the network segment. Only packets addressed to a
specific destination host outside the network segment are
allowed to pass through the bridge. | | 1 |
| A ISDN PRI circuit can be described as which of the following?
A.) 24 B channels and 1-64Kbps D channel
B.) 23 B channels and 1-64Kbps D channel
C.) 2-D channels and 1-C channel
D.) 2-64Kbps B channels and 1-16Kbps D channel | | 1 |
| Which layer is responsible for framing?
A.) Application
B.) Data Link
C.) Physical
D.) Network
E.) Transport | | 2 |
| Which layer defines bit synchronization?
A.) Application
B.) Network
C.) Transport
D.) Physical
E.) Session
F.) Session | | 1 |
| Hi,can anyone explain me in brief about ccna security.
waiting for your answer | | 2 |
| Identify the command that displays traffic statistics on
serial0/1?
A.) display interface serial0/1
B.) show interface serial0/1
C.) show seria0/1 stats
D.) show interface serial0/1 stats | | 1 |
| Identify the command to configure a description on an interface?
A.) Router> description Finance department
B.) Router(config)# description Finance department
C.) Router(config-if)# description Finance department
D.) Router# description Finance department | | 1 |
| take a pen and copy before solving that question
there is a router name Ra
there is two switch sw1 and sw2
sw1 is coneceted through fa0/1 interface of router Ra
sw2 is conected through the fa1/1
serai interface of router s0/1 conected through the isp
with it ip address 192.168.1.1
now therer are three host conexted through the sw1 and
having ip
host1=10.1.2.1
host2=10.1.2.2
host3=10.1.2.3
now there is also 3ree host conected through switch 2 i.e
sw2 having ip
host4=10.1.1.1
host 5=10.1.1.2
host 6=10.1.1.3
now i think u have made corect confrigation.now questios is
started
network admin configure the Ra router in that fassion
Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255
Ra(config)#line vty 0 4
ra(config)#access-class 2 in
now question is that why should network admnistratoe do it
in this maneer
A to give access sw1 host to acess internet
B to prevent sw1 host from acessing comand promt
c to prevent sw2 host from accessing console of router ra
D to give sw2 host access to the enternet
e prevent sw1 host from accessing internet
f to prevent sw1 host from acessing the sw2 host network
isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6)
|
|
(sw1)------host 1,2,3
this is not exect digarm but help to derive the diagram
plz answer as soon as possible
| AT&T | 6 |
| Which two types of route table entries are used by a Layer 3
router to determine the appropriate path to destination?
(Choose two)
A. static route entry
B. default route entry
C. Dynamic route entry
D. temporary route entry
E. permanent route entry | | 1 |
| |
| For more CCNA Interview Questions Click Here |
along with your userid / name. ThanQ
Site Map
