| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which two steps are part of the process of creating Frame
Relay subinterfaces on a point to point connection? (Choose
two)
A. configure the router to forward all broadcast packets
B. remove any network address assigned to the physical interface
C. configure the local data link connection identifier
(DICI) for the subinterfaces
D. cartoon the total committed information rate (CIP)
available among the subinterfaces | | 1 |
| Which of the following would be displayed by the command
'SHOW CDP
NEIGHBOR DETAIL'?
A.) The incoming/outgoing port.
B.) The hardware platform.
C.) One address per protocol.
D.) Amount of Flash Memory Available
E.) The routers hostname.
F.) The subnet mask, if IP is configured. | | 1 |
| Which command enables directly connected network 199.55.72.0
to be used by RIP?
A. Router(config router)# rip 199.55.0.0
B. Router(config router)# rip 199.55.72.0
C. Router(config router)# network 199.55.0.0
D. Router(config router)# network 199.55.72.0 | | 1 |
| Identify the OSI layer associated with bits?
A.) Physical
B.) Network
C.) Binary
D.) Data link | | 2 |
| Identify the IPX standard access-list number range?
A.) 600 - 699
B.) 1000 - 1099
C.) 1 - 99
D.) 100 - 199
E.) 800 - 899 | | 1 |
| Which protocol will let neighbor routers know if your
internetwork
experienced congestion on a serial port?
A.) BootP
B.) IP
C.) ICMP
D.) ARP
E.) FTP
F.) RARP | | 3 |
| Using the access-list command, 'access-list 1 deny 2.2.2.2',
what
else must be done to stop host 2.2.2.2 from sending any
traffic out of
physical interface E0,
while still allowing other traffic?
A.) In global mode, Add a line - 'access-list 1 permit
0.0.0.0 255.255.255.255'
B.) On interface E0, Add a line - 'access-group 1 in'
C.) In global mode, Add a line - 'access-list 1 permit all'
D.) On interface E0, Add a line - 'access-list 1 in'
E.) On interface E0, Add a line - 'access-list 1 out'
F.) On interface E0, Add a line - 'ip access-group 1' | | 1 |
| Which statement is true?
A. While bridges are used to segment networks, they will not
isolate broadcast or multicast packets.
B. A bridge looks at every packet within its network segment
and works like a hub re-broadcasting the packet if the
destination is within its network segment.
C. A bridge maintains a table of the IP addresses of the
hosts within its network segment and forwards the packet
directly to the destination based upon the IP address.
D. A bridge resets the hop count by keeping all packets
within the network segment. Only packets addressed to a
specific destination host outside the network segment are
allowed to pass through the bridge. | | 1 |
| In the command "router igrp 109" what does 109 signify?
A. an autonomous system
B. any network number which the router is attached to
C. the allowable length of the routing table
D. the network socket number | | 1 |
| Which three of the following are true statements about
connection-oriented
sessions?
A.) The segments delivered are acknowledged back to the
sender upon
their reception
B.) Any segments not acknowledged are retransmitted by the
receiver
C.) A manageable data flow is maintained in order to avoid
congestion,
overloading and loss of any data
D.) Segments are sequenced back into their proper order upon
arrival at
their destination | | 3 |
| Which of the following will apply IPX sap access list 1010 for
incoming traffic, assume you are at the interface configuration?
A.) ipx input-sap-filter 1010 in
B.) ipx input-sap-filter 1010
C.) ipx access-group 1010 in
D.) ipx access-list 1010 in | | 1 |
| Which three basic switch functions increase available
bandwidth on the networks? (Choose three)
A. loop avoidance
B. address learning
C. hop count limiting
D. broadcast filtering
E. packet forward/filtering
F. broadcast packet hop count learning/forward/filtering | | 1 |
| Which layer manages protocol access to the Network layer?
A.) Datalink - MAC Sublayer
B.) Datalink - LLC Sublayer
C.) Transport
D.) Session
E.) Network | | 1 |
| Which statement about Ethernet networks is true?
A. The advantage of a full duplex is the ability to transmit
data over 111 cable
B. Full duplex Ethernet requires a point-to-point connection
when only two nodes are present
C. Ethernet switches can use full duplex mode to connect
multiple nodes to a single pod of a switch
D. Half duplex is a cut through packet processing method
that is vow fast little error correction Full duplex is a
store and forward method that is slower but has better error
correction | | 1 |
| Identify the 2 methods to modify the routers boot sequence?
A.) Setup program
B.) Boot system commands
C.) RXBoot
D.) Config-register | | 1 |
| Identify the type of hardware required to connect a Token ring
network to an Ethernet network?
A.) Repeater
B.) TR-Enet
C.) Router
D.) Token Ring to Ethernet translation hub | | 1 |
| What key do you use to view the last command?
A.) Ctrl+X
B.) Ctrl+Z
C.) Ctrl+E
D.) Ctrl+P | | 1 |
| Which command will display the IPX routing table?
A.) show routes
B.) show routes ipx
C.) show routes protocol=ipx
D.) show ipx
E.) show ipx route | | 1 |
| What is the command to manually enter a static route?
A.) IP route network
B.) IP route
C.) IP route < destination network>
D.) IP route | | 1 |
| What is the maximum hop count for Link-State protocols?
A.) 15
B.) there is no hop count limit
C.) 256
D.) 16 | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
