| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| X.25 is characterized by layer 2 identifiers, and what else?
A.) Virtual Lan's
B.) Session Layer
C.) Transport Layer
D.) Routing Updates
E.) PVC's | | 1 |
| Which of the following would be displayed by the command
'SHOW CDP
NEIGHBOR DETAIL'?
A.) The incoming/outgoing port.
B.) The hardware platform.
C.) One address per protocol.
D.) Amount of Flash Memory Available
E.) The routers hostname.
F.) The subnet mask, if IP is configured. | | 1 |
| Identify the following components of the IPX address
2e.0000.0065.ed43
A.) Not a valid IPX address
B.) Network = 2e, Subnet = 0000, Node = 0065.ed43
C.) Network = 2e.0000, Node = 0065.ed43
D.) Network = 2e, Node = 0000.0065.ed43 | | 1 |
| Given an IPX network with redundant paths, what command will
configure load balancing?
A.) ipx load-balance
B.) ip maximum-paths 2
C.) ipx maximum-paths 2
D.) ipx load-share | | 1 |
| Which statement is true regarding half duplex?
A.) Only works in a point-to-point configuration
B.) Allows for transmitting and receiving but not a the same
time
C.) Allow for transmitting and receiving of data simultaneously
D.) Doubles the bandwidth | | 1 |
| In transport layer, for connection oriented communication
Three way handshake process is there to establish a
connection. So question is that, when a host send an ACK
messages to another host with host intend to establish a
connection, the source host send it as Broadcast or unicast
message? Cud anyone explain this.
Thanks in advance. | HCL | 3 |
| Most routing protocols recognize that it is never useful to send
information about a route back out the direction from which
the original
packet came. This is an example of which routing technology?
A.) Split Horizon
B.) LMI
C.) Triggered Updates
D.) Poison Reverse
E.) SYN, ACK
F.) DLCI | | 1 |
| Identify the keystroke used to terminate the setup mode?
A.) Ctrl-K
B.) Crtl-C
C.) Ctrl-Z
D.) Crtl-End | | 1 |
| Which ISDN specification deals with call Setup and Teardown?
A.) Q-Series
B.) J-Series
C.) I- Series
D.) C- Series
E.) F-Series | | 1 |
| What information is provided by the local management
interface (LMI)?
A.) LMI encapsulation type
B.) The current DLCI values
C.) The status of virtual circuits
D.) The global or local significance of the DLCI values | | 1 |
| hi shain/sudeep and rest of all plz answer these question
for help some one as soon as possible
what is stub area
what is transit area
let there are three area in ospf a0 a2 and a3 if a2 and a3
is coneted
through each other will they comnicate | | 3 |
| Describe End to End network services: (Choose all that apply)
A.) Best Route selection
B.) Accomplished Segment by Segment, each segment is autonomous
C.) Flow Control & Data Integrity
D.) Best efforts packet delivery | | 1 |
| Identify the definition of demarcation?
A.) Date in which the WAN service contract expires
B.) Cabling which extends from the WAN service provider to
the customer
C.) Division of responsibility, where the CPE ends and the
local loop
begins
D.) Equipment which is located at the customer premises | | 1 |
| What is the routing algorithm used by RIP and IGRP?
A.) OSPF
B.) Link-state
C.) Dynamic
D.) Distance Vector | | 2 |
| Identify the purpose of the Ping command?
A.) Share routing information with a neighbor router
B.) Transmit user data when buffers are full
C.) Test connectivity at layer 3
D.) Test entire protocol stack | | 2 |
| Which OSI layer provides best effort end to end packet delivery?
A.) Data-Link
B.) Presentation
C.) Network
D.) Transport
E.) Physical
F.) Application | Barnes-and-Noble | 2 |
| Which global configuration command will tell the router to load
the IOS file 'IOS_filename' from FLASH memory at the next boot?
A.) boot system flash
B.) boot system flash IOS_filename
C.) boot system IOS_filename flash
D.) boot system tftp IOS_filename tftp_address
E.) config-register 0x0102 IOS_ filename | HSBC | 1 |
| 8. When is Frame Tagging used?
A. When you install repeaters in your network
B. When you install bridges in your network
C. When you install routers in your network
D. When you use Switches configured with multiple VLANS
| | 4 |
| Identify the components in the following command 'interface
serial0/1/1'
A.) Serial interface, port number 0, slot 1, port adapter 1
B.) Serial interface, slot 1, port number 1, port adapter 0
C.) Serial interface, slot 0, port adapter 1, port number 1 | | 2 |
| Which of the following provide correct information about a
protocol at the transport layer of the OSI model?
A.) UDP - Provides Connectionless datagrams service
B.) TCP - Provides Connection Oriented Services
C.) SMTP - Provides Mail Exchange
D.) IP - Route determination
E.) TCP - Provides Flow Control and Error Checking
F.) FTP - Transfers of Files | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
