| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| what is the difference between osi and tcp ? | | 6 |
| 2. What are the valid ways to segment a LAN? (Choose all
that apply)
A. Repeater
B. Bridge
C. Switch
D. Router
| | 2 |
| What is the UDP datagram format?
A. Source Port - 16 bits, Destination Port - 16 bits, Length
- 16 Bits, Checksum - 16 bits, Data
B. Destination Port - 16 bits, Source Port - 16 bits, Length
- 16 Bits, Checksum - 16 bits, Data
C. Source Port - 16 bits, Destination Port - 16 bits,
Checksum - 16 Bits, Length - 16 bits, Data
D. Source Port - 8 bits, Destination Port - 8 bits, Length -8
Bits, Checksum - 8 bits, Data | | 1 |
| (1)what is "rtp" and how it work,
(2)what is diffrence between igrp and eigrp
(3)the slection prcedure of dr and bdr is depend open
(4)why frame really is called nbma
(5)what is ppp
(6) what is diffrence b/w tcp and udp
(7) how can we implement ospf protocall on any router
(8)whta is as nomber
(9)what is AD value
(10)what is the broadcast id,n/w id and number of vallid
host of the 255.255.255.128/25 195.168.10.10/25
(11) what is stub network
(12) what is contigues n/w
(13)on which type of router we can implement default routing
(14)what is diffrence b/w hub switch;switch router,
(15)what is v lan
(16)what is the diffrence b/w link sate protocal and
distance vector protocall
(17)what is synchoransh mode of data transfer and
asynchronash mode of data transfer
(18) question on lab,
belive me frnds there are 20 questions and 5 questions on
lab implimentaion.around 1.1/2 hour i was in interview room
and after givieng 17 right answera and 4 in lab i got
slected
try to give answer
if any difficulty or any prob plz email me on
jitenderasinha.it@gmail.com
if any one of you havae boson netsim plz also intimate me
| | 4 |
| A user device that connects to a DCE must be which of the
following?
A.) DTE
B.) CPE
C.) Demarc
D.) DCE
E.) CO | | 1 |
| The command 'debug ip rip' will do which of the following?
A.) Show Neighbor Info.
B.) Display RIP routing updates.
C.) Show routing table changes.
D.) Show all IP traffic.
E.) This is not a valid router command.
F.) Cause the router to respond with 'Ambiguous command' | | 1 |
| Which command displays the IPX SAP table?
A.) show ipx sap
B.) show sap
C.) show ipx interface
D.) show ipx servers
E.) show ipx | | 1 |
| At which layer of the OSI model does the ping command operate?
A. session
B. network
C. transport
D. maintenance | jetking | 6 |
| Identify the purpose of the Trace command?
A.) Explorer packet transmitting routing information
B.) Test connectivity
C.) Determine the path a packet is taking through the network
D.) Transmits user data when buffers are full | | 1 |
| To monitor ipx traffic on a network, what command would you use?
A. debug ipx transaction
B. show ipx traffic
C. show ipx events
D. display ipx traffic | | 2 |
| What does the acronym ARP stand for?
A.) Address Resolution Phase
B.) ARP Resolution Protocol
C.) Address Resolution Protocol
D.) Address Recall Protocol | | 1 |
| Given an IPX network with redundant paths, what command will
configure load balancing?
A.) ipx load-balance
B.) ip maximum-paths 2
C.) ipx maximum-paths 2
D.) ipx load-share | | 1 |
| Identify the 3 guidelines for routers in the same autonomous
system?
A.) Must be configured for RIP
B.) Interconnected
C.) Assigned the same autonomous system number
D.) Configured for the same routing protocol
E.) Must be same model of router | | 1 |
| How often does IP RIP send out routing table updates by default?
A.) They send complete updates every 30 seconds
B.) They send partial updates every 30 seconds
C.) They send complete updates every 60 seconds
D.) They send partial updates every 60 seconds | | 2 |
| What are characteristics of UDP
A. It is reliable and acknowledged
B. It is unreliable and acknowledged
C. It is reliable and unacknowledged
D. It is unreliable and unacknowledged | | 2 |
| As a system administrator, you perform an extended ping at
the privileged EXEC prompt. As part of the display, you see
"Set DF bit in IP header? [yes] :" What would happen if you
answered no at the prompt.
A. This lets the router fragment the packet.
B. It tells the router not to fragment the packet.
C. This lets the router direct the packet to the destination
it finds in its routing table.
D. It tell the router to send the packet to the next hop
router. | | 1 |
| What is the difference between RIP & RIPng????
Can anyone explain it..!!!
Thank u in advance. | | 1 |
| Which is true regarding store-and-forward switching method?
A.) Latency varies depending on frame-length
B.) Latency is constant
C.) It is default for all Cisco switches
D.) It only reads the destination hardware address before
forwarding the
frame | | 1 |
| Identify the IPX standard access-list number range?
A.) 600 - 699
B.) 1000 - 1099
C.) 1 - 99
D.) 100 - 199
E.) 800 - 899 | | 1 |
| Using the TCP/IP protocol suite, a message is sent from host
A to a destination IP address on the same LAN. How does
host A determine the destination of a MAC address?
A. It uses a proxy APP
B. It uses APP requests
C. It uses PARP requests
D. It uses a router lookup table | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
