ALLInterview.com :: Home Page KalAajKal.com
 Advertise your Business Here     
Browse  |   Placement Papers  |   Company  |   Code Snippets  |   Certifications  |   Visa Questions
Post Question  |   Post Answer  |   My Panel  |   Search  |   Articles  |   Topics  |   ERRORS new
   Refer this Site  Refer This Site to Your Friends  Site Map  Bookmark this Site  Set it as your HomePage  Contact Us     Login  |  Sign Up                      
Do you have a collection of Interview Questions and interested to share with us!!
Please send that collection to along with your userid / name. ThanQ
Google
 
Categories  >>  Certifications  >>  Cisco Certifications  >>  CCNA
 
 


 

 
 CCNA interview questions  CCNA Interview Questions
 CCDA interview questions  CCDA Interview Questions
Question
In the setup dialog, what do the square brackets indicate?

A. current or default spores

B. hard coded values that cannot be modified

C. values entered by the administrator but not saved

D. values that must be written to PAVRAM before becoming enabled
 Question Submitted By :: Guest
I also faced this Question!!     Rank Answer Posted By  
 
  Re: In the setup dialog, what do the square brackets indicate? A. current or default spores B. hard coded values that cannot be modified C. values entered by the administrator but not saved D. values that must be written to PAVRAM before becoming enabled
Answer
# 1
Answer: A
 
Is This Answer Correct ?    0 Yes 0 No
Guest
 

 
 
 
Other CCNA Interview Questions
 
  Question Asked @ Answers
 
Write an access list line which will deny node 20.0.2.1 to anywhere on your network using DNS via UDP. Don't worry about the other access list lines.  2
Which layer is responsible for determining if sufficient resources for the intended communication exists? A.) Application B.) Network C.) Session D.) Presentation E.) Transport  1
Identify the command that configures serial0 for PPP encapsulation? A.) Router(config)# encapsulation ppp B.) Router(config-if)# encapsulation serial ppp C.) Router(config-if)# encapsulation ppp D.) Router# encapsulation ppp  1
What is CRC and which layer it use? CMS3
The Datalink layer works with which of the following: A.) Packets B.) Bits C.) Globules D.) Frames E.) Segments  2
The command 'debug ip rip' will do which of the following? A.) Show Neighbor Info. B.) Display RIP routing updates. C.) Show routing table changes. D.) Show all IP traffic. E.) This is not a valid router command. F.) Cause the router to respond with 'Ambiguous command'  1
As the system administrator, you enter the following commands at the command prompt: ipx routing access-list 800 permit 2b 4d int e0 ipx network 4d ipx access-group 800 out int e1 ipx network 2b int e2 ipx network 3c What did these command accomplish? A. Traffic from network 4c destined for network 4d will be forwarded out Ethernet0. B. Traffic from network 3c destined for network 4d will be forwarded out Ethernet0. C. Traffic from network 2b destined for network 4d will be forwarded out Ethernet0. D. Traffic from network 4d destined for network 2d will be forwarded out Ethernet0.  1
Identify 3 characteristics regarding CDP? A.) On by default B.) Shows only directly connected neighbors C.) Requires IP or IPX D.) 60 second update interval by default E.) 30 second updates interval by default  1
How do you disable CDP on the entire Router? A.) Router#no cdp run B.) Router(config-if)# no cdp enable C.) Router(config)# no cdp enable D.) Router(config)# no cdp run  1
How many access lists are allowed per interface? A. One per port, per protocol B. Two per port, per protocol C. Unlimited D. Router interface +1 per port.  2
Choose three reasons why the networking industry uses a layered model: A.) It facilitates systematic troubleshooting B.) It allows changes in one layer to occur without changing other layers C.) It allows changes to occur in all layers when changing one protocol D.) It clarifies how to do it rather than what general function to be done E.) It clarifies what general function is to be done rather than how to do it  1
Which layer of the 7 layer model is responsible for representing the application information between 2 different OS's? For example, converting ASCII to EBCIDIC. A.) Transport B.) Application C.) Physical D.) Session E.) Presentation F.) Network  2
What 3 sources can configuration commands be placed into RAM? A.) HP Openview B.) Console C.) Vterminal D.) TFTP server E.) NVRAM  1
What command will not display the status of to1? A.) show int to1 B.) show to1 C.) show interface to1 D.) show interface  1
Which of the following is a layer 2 device? A.) Switch B.) Router C.) Repeater D.) Hub  4
Which of the following are characteristics of UDP? A.) UDP is connection oriented. B.) UDP is used with TFTP. C.) UDP is unreliable. D.) UDP is connectionless. E.) UDP is at the transport layer. F.) UDP uses no acknowledgements.  1
Which layer is responsible for flow control, acknowledgement, and windowing? A.) Transport B.) Network C.) Application D.) Session E.) Physical F.) Data Link  2
Which of the following will apply IPX sap access list 1010 for incoming traffic, assume you are at the interface configuration? A.) ipx input-sap-filter 1010 in B.) ipx input-sap-filter 1010 C.) ipx access-group 1010 in D.) ipx access-list 1010 in  1
4. What is a disadvantage to using bridges in your network? A. Filters by MAC address B. Stops broadcast storms C. Doesn't stop broadcast storms D. Can only use up to 4 bridges in any LAN  3
Which of the following are examples of the Network Layer? A.) Token Ring B.) LLC C.) SQL D.) IP E.) TCP F.) IPX  3
 
For more CCNA Interview Questions Click Here 
 
 
 
 
 
   
Copyright Policy  |  Terms of Service  |  Help  |  Site Map 1  |  Articles  |  Site Map  |   Site Map  |  Contact Us interview questions urls   External Links 
   
Copyright © 2007  ALLInterview.com.  All Rights Reserved.

ALLInterview.com   ::  Forum9.com   ::  KalAajKal.com