| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Access lists are numbered. Which of the following ranges
could be
used for an IP access list?
A. 600 - 699
B. 100 - 199
C. 1 - 99
D. 800 - 899
E. 1000 - 1099 | | 1 |
| Which three are typical operational phases in a basic
connection oriented network service?
A. call setup
B. data transfer
C. load balancing
D. call termination
E. caller ID
F. call prionflication
G. data segmentation
H. data and momma
I. data link identification
J. callering book | | 1 |
| You need to come up with a TCP/IP addressing scheme for your
company. How many network IDs must you allow for when you
define the
subnet mask for the network?
A.) One for each WAN link
B.) One for each router interface
C.) One for each NIC installed in each client
D.) One for each subnet with hosts
E.) One for each host ID | | 1 |
| what is difference between hub and router..... | Thomson | 5 |
| Which show command should you use to view Frame Relay Local
Management Interface (LMI) Frame statistics?
A. show lmi
B. show ip route
C. show interface
D. show statistics
E. show frame-relay lmi | | 1 |
| How can an Ethernet switch improve network performance?
Choose three | | 1 |
| Identify the 2 rules used when configuring a Distance Vector
routing protocol?
A.) Physically connected network(s)
B.) Configure the classful address, no subnets
C.) Enable CDP so neighbors can be detected
D.) Configure all networks in Area0 | | 1 |
| Which three statements about Frame Relay configurations
using subinterfaces is true? (Choose three)
A. Each subinterface is conferred either multipoint or point
to point
B. Any network address must be removed from the physical
interface
C. The configuration of subinterfaces is done in router
(config-if)# mode
D. Frame Relay encapsulation must be conferred on each
subinterface | | 1 |
| What is a key use of a device hardware address?
A. to obtain a vendor code / serial number from the user
B. to transmit a frame from one Interface to another Interface
C. to transmit a packet from one local device to another
local device
D. to transmit data from one local device to a remote device
across the internet
E. to contain logical information about the device to use
for end-to-end transmission | | 1 |
| In regards to the ISDN BRI standard, which channel is used for
control?
A.) B
B.) D
C.) E
D.) I
E.) Q | | 1 |
| What does the Spanning Tree Algorithm (STA) do?
A.) Restore lost frames
B.) Builds routing tables for routing through an internetwork
C.) Forward packets through a switch
D.) STA is implemented by STP to prevent loops | | 1 |
| Identify the command to display the IP routing table?
A.) show route
B.) show ip route
C.) show ip table route
D.) show ipx route | | 1 |
| Identify the statement which connects access-list 101 inbound to
interface e0?
A.) Router(config-if)# ip access-group 101 in
B.) Router(config-if)# ip access-group 101
C.) Router(config)# ip access-group 101 e0 in
D.) Router(config)# ip access-group 101 e0 in | | 1 |
| HOW MPLS IS DIFFERENT FROM OSPF? WHY NOW A DAYS MPLS IS
PREFERED OVER ANY NETWORK PROTOCOL? | Bank-Of-India | 1 |
| The CSMA/CD Ethernet IEEE committee is defined as which of the
following?
A.) 802.2
B.) 802.3
C.) 802.4
D.) 802.5 | | 1 |
| Identify the command to configure DLCI 100 on an interface e0?
A.) Router(config)# frame-relay local-dlci 100
B.) Router(config)# frame-relay local-dlci 100 int e0
C.) Router(config-if)# frame-relay local-dlci 100
D.) Router(config-if)# frame-relay local-dlci 100 int e0 | | 1 |
| Which of the following is a characteristic of a switch, but
not of
a repeater?
A.) Switches forward packets based on the IPX or IP address
in the frame
B.) Switches forward packets based on the IP address in the
frame
C.) Switches forward packets based on the MAC address in the
frame
D.) Switches forward packets based only on the IP address in
the packet | | 2 |
| You receive "input filter list is 800 and output filter list is
801" as part of the output from a show interfaces command.
What kind of
traffic are you filtering?
A. IPX/SPX
B. TCP/IP
C. LocalTalk
D. DDR | | 1 |
| Identify the 2 commands that save the running-config to a TFTP
server?
A.) write running tftp
B.) copy running network
C.) copy running tftp
D.) write network | | 1 |
| Which layer hides details of network dependent information from
the higher
layers by providing transparent data transfer?
A.) Transport
B.) Physical
C.) Data Link
D.) Session
E.) Application
F.) Network | | 2 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
