| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| How do you disable CDP on the entire Router?
A.) Router#no cdp run
B.) Router(config-if)# no cdp enable
C.) Router(config)# no cdp enable
D.) Router(config)# no cdp run | | 1 |
| Which of the following is an example of the Network Layer?
A.) LLC
B.) SQL
C.) Token Ring
D.) IPX
E.) SPX | | 1 |
| Identify the mode reflected by the following prompt 'Router'?
A.) Setup
B.) RXBoot
C.) Boot mode
D.) Privileged exec mode | | 1 |
| Which command line option will determine what traffic is
interesting enough to establish a dialup connection?
A.) dialer map
B.) dialer string
C.) dialer in-band
D.) dialer-list
E.) dialer negotiation | | 1 |
| Which two of the following are valid ways to have multiple
encapsulation types on a single interface?
A.) This is not possible
B.) subinterfaces
C.) additional physical interfaces
D.) secondary addresses | | 2 |
| When you use the Cisco IOS command show configuration on a
router which part of the output shows the specific conferred
IP addresses and shored masks?
A. the IP host table
B. the interfaces output
C. each section of the output
D. the global configuration statements
E. the section under the autonomous system number | | 1 |
| Identify the purpose of the Ping command?
A.) Share routing information with a neighbor router
B.) Transmit user data when buffers are full
C.) Test connectivity at layer 3
D.) Test entire protocol stack | | 1 |
| What are hold-downs used for?
A.) To prevent regular update messages from reinstating a
route that has
come back up
B.) Information received on an interface cannot be sent back
out the
same interface
C.) To prevent regular update messages from reinstating a
route that has
gone down
D.) To hold the routing table from being sent to another router | | 1 |
| Which 3 statements describe default encapsulation and LMI type
configuration?
A.) There are only four encapsulations and 3 LMI type options
B.) The LMI type config term options
C.) In release 11.3 the LMI type is autosensed
D.) The default LMI is Cisco
E.) IETF encap must be configured unless the connecting
routers are both
cisco | | 1 |
| Identify 2 characteristics of PPP?
A.) Uses LLC to establish the link
B.) Default serial encapsulation
C.) Support multiple layer 3 protocols
D.) Offers two types of authentication; PAP and CHAP | | 1 |
| Identify the command to display the Frame Relay map table?
A.) Router# display frame-relay map
B.) Router# show frame-relay map
C.) Router(setup)# show frame-relay map
D.) Router# show map frame-relay | | 1 |
| Which OSI layer end to end communication, segmentation and
re-assembly?
A.) Network
B.) Transport
C.) Physical
D.) Application
E.) Data-Link
F.) Presentation | | 1 |
| What does the following series of commands accomplish?
router igrp 71
network 10.0.0.0
router igrp 109
network 172.68.7.0
A. It isolates networks 10.0.0.0 and 172.68.7.0.
B. It loads igrp for networks 109 and 71.
C. It disables RIP.
D. It disables all routing protocols. | | 1 |
| What is switch priority & why it is used???? | ADP | 4 |
| Which layer is responsible for determining if sufficient
resources
for the
intended communication exists?
A.) Application
B.) Network
C.) Session
D.) Presentation
E.) Transport | | 2 |
| There is an emergency fall-back 'skeleton' IOS stored in
read only
memory on all Cisco routers. What command would make the
router load the
IOS from
Read Only Memory?
A.) reload rom
B.) boot system rom
C.) load ios bootflash
D.) load ios rom
E.) bootsystem skeleton | | 2 |
| What is the default size of a standard ping on a Cisco router?
* A: 100 bytes
* B: 32 bytes
* C: 10 bytes
* D: 16 bytes
| CMS | 2 |
| What is the difference between OSPF Exteral Type 1 (O E1) &
External Type 2 (O E2) routes???? | | 3 |
| You want to segment a network. The network is running SNA and
Netbios. Which device should NOT be used to segment the network?
A.) A store and forward switch.
B.) A router.
C.) A Catalyst 5000.
D.) A cut-through switch.
E.) A bridge. | | 1 |
| Which three devices can be used to convert the user data
from the
DTE into a form acceptable to the WAN service's facility?
A. Modem
B. CSU/DSU
C. TA/NT1
D. CO
E. SS7 | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
