Which command specifies a second subinterface on serial interface 0? A.

Advertise your Business Here

Refer this Site

Login | Sign Up


	Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff HERE

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

Which command specifies a second subinterface on serial
interface 0?

A. interface s 0.2 point-to-point

B. interface 2 s.0 point-to-point

C. suberinterface 2.s 0 point-to-point

D. interface s 0 sub 2 point-to-point

E. interface s 0.1 point-to-point sub 2

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: Which command specifies a second subinterface on serial interface 0? A. interface s 0.2 point-to-point B. interface 2 s.0 point-to-point C. suberinterface 2.s 0 point-to-point D. interface s 0 sub 2 point-to-point E. interface s 0.1 point-to-point sub 2

Answer
# 1

Answer: A

Is This Answer Correct ?

2 Yes

0 No

Guest

Question	Asked @	Answers
Other CCNA Interview Questions


Identify the following components of the IPX address 2e.0000.0065.ed43 A.) Not a valid IPX address B.) Network = 2e, Subnet = 0000, Node = 0065.ed43 C.) Network = 2e.0000, Node = 0065.ed43 D.) Network = 2e, Node = 0000.0065.ed43		1
LMI operates between the Frame Switch and what other device? A.) CPE device B.) Another Frame Switch C.) X.25 switch D.) Novell File Server		1
Which OSI Reference Layer is concerned with path determination? A.) Datalink B.) Physical C.) Network D.) Transport E.) Session		2
Identify the purpose of ICMP? A.) Avoiding routing loops B.) Send error and control messages C.) Transporting routing updates D.) Collision detection		2
Which statement about the Point to Point Protocol (PPP) is true? A. PPP supports TCP/IP but not Novell IPX B. PPP is being phased out of existence by the Serial Line Internet Protocol (SLIP) C. PPP providces router to router and host to network connections over both synchronous and asynchronous circuits D. PPP is an ITU T and ANSI standard that defines the process for sending data over a packet switched data network (PSDN)		1
In the setup dialog, what do the square brackets indicate? A. current or default spores B. hard coded values that cannot be modified C. values entered by the administrator but not saved D. values that must be written to PAVRAM before becoming enabled		1
Which protocol will send a message to routers if a network outage or congestion occurs? A.) ARP B.) TCP C.) IP D.) ICMP		1
Which of the following is an example of the Network Layer? A.) TCP B.) IP C.) SQL D.) Token Ring E.) LLC		2
Which frame has a Type field to identify the upper-layer protocol? A.) 802.3 B.) 802.2 C.) 802.5 D.) Ethernet_II		1
Put the following steps of encapsulation into the correct order: 1) The data is broken into segments to be organized 2) Frames are converted to 1s and 0s to be put on the wire 3) Packets are converted into frames 4) Information that users enter is converted into data 5) The segments are changed to packets to be routed A.) 4, 1, 3, 2, 5 B.) 4, 5, 1, 3, 2 C.) 2, 3, 1, 4, 5 D.) 4, 1, 5, 3, 2		2
What is the juncture at which the CPE ends and the local loop portion of the service begins? A. Demarc B. CO C. Local loop D. Last-mile		1
what is routing and routed protocol ?		7
What is the default bandwidth of a serial connection? A.) 1200 baud B.) 1.544 Mbps (T1) C.) 10 Mbps D.) 96Kpbs		1
Identify the mode reflected by the following prompt 'Router'? A.) Setup B.) RXBoot C.) Boot mode D.) Privileged exec mode		1
Identify 2 PPP characteristics? A.) Is proprietary to Cisco B.) Supports authentication C.) Support compression D.) Run on a multi-access network		1
What is the function of Layer 2 Switch?		1
How does inter- VLAN communication take place? A. It takes place through any Cisco router B. It takes place through a Cisco router that can run ISL C. It takes place through a router but this disables all the router a security and filtering functionality for the VLANS D. For nonroutable protocals (e.g. NetBeui) the router provides communications between VLAN domains E. Inter-VLAN communication is not possible because each VLAN is a separate broadcast domain		3
Identify the purpose of the Trace command? A.) Explorer packet transmitting routing information B.) Test connectivity C.) Determine the path a packet is taking through the network D.) Transmits user data when buffers are full		2
Which OSI layer provides mechanical, electrical & procedural specifications for activating, maintaining physical link? A.) Presentation B.) Network C.) Application D.) Physical E.) Transport F.) Data-Link		1
What is the standard ISDN term for a native ISDN modem? A.) ET B.) LE C.) TE2 D.) TE3 E.) TA		1

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com