| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| what is difference between hub and router..... | Thomson | 5 |
| Identify the command that will display the RIP routes
entering and
leaving the router?
A.) Router(config)# debug ip rip
B.) Route# debug ip rip
C.) Router>debug ip rip
D.) Router# debug rip routes | | 1 |
| what is the distance betwwen link stae routing protocl and
distance vector
who have the best convergence toplogy
eigrp conatain 3 table name them
what the toplogy table contain | IBM | 5 |
| What protocols can you use while testing Trace?
A.) DECnet
B.) CLNS
C.) IP
D.) Old Vines
E.) Vines
F.) Chaos | | 1 |
| What are four ways that Fast Ethernet compares to 10BaseT
Ethernet? (Choose four)
A. Fast Ethernet uses the same Maximum Transmission Unit (MTU)
B. Fast Ethernet is based on an extension to the IEEE 802.3
specification
C. Fast Ethernet uses the same Media Access Control (MAC)
mechanisms
D. Fast Ethernet preserves the frame format that is used by
10BaseT Ethernet
E. Fast Ethernet errors a speed increase one hundred times
that of the 10BaseT Ethernet | | 1 |
| Identify the command that forces the router to load into ROM
mode
upon a reload?
A.) boot system rom
B.) rom boot
C.) boot system flash rom
D.) boot router rom | | 1 |
| Identify the effect of Ctrl-Z?
A.) Exits back to privileged exec mode
B.) Disconnect from the router
C.) Abort the ping operation
D.) Exits privileged exec mode | | 1 |
| What's the default CDP holdtime in seconds for Cisco routers?
A.) 30 seconds
B.) 180 seconds
C.) 90 seconds
D.) 60 seconds | | 3 |
| What is the result of using a hierarchical addressing framework?
A. increased availability of addresses
B. decreased distance between routers
C. increased router memory requirements
D. no need to maintain routing information | | 2 |
| CO is an acronym for which of the following?
A.) Central Office
B.) Capital Office
C.) Central Operator
D.) Company Office | | 1 |
| Which OSI Reference Layer is concerned with path determination?
A.) Datalink
B.) Physical
C.) Network
D.) Transport
E.) Session | | 2 |
| Layer 1 and Layer 2 devices must forward a broadcast.
Which of the following devices fall into this category?
Gateway
Switch
Router
All of the above.
| | 1 |
| The command 'debug ip rip' will do which of the following?
A.) Show Neighbor Info.
B.) Display RIP routing updates.
C.) Show routing table changes.
D.) Show all IP traffic.
E.) This is not a valid router command.
F.) Cause the router to respond with 'Ambiguous command' | | 1 |
| What is the maximum number of subnets that can be assigned
to networks when using the address 172.16.0.0 with a subnet
mask of 255.255.240.0? (Assume older version UNIX
workstations are in use.)
A. 16
B. 32
C. 30
D. 14
E. It is an invalid subnet mask for the Network. | | 1 |
| The two sublayers of the IEEE Data Link Layer are which of the
following?
A.) Link and Logical Control
B.) Data Link and LLC
C.) Logical Link Control and Media Access Control
D.) Data Link and MAC | | 2 |
| What is the Network Layer of the OSI responsible for?
A.) Bridging
B.) Routing packets through an internetwork
C.) Regenerating the digital signal
D.) Gateway services | | 1 |
| Cisco's implementation of ISDN BRI has multi protocol support,
SNMP MIB support, and what other features?
A.) Call waiting
B.) Compression
C.) ADSL
D.) 1.544 Mbps
E.) Call screening
F.) Negative 'G' support | | 1 |
| Which command would configure Interface E0 with an IP address of
12.23.4.5 using a Subnet mask of 255.255.255.0 ?
A.) ip address 12.23.4.5 255.255.255.0
B.) ip address 12.23.4.5 /24
C.) ip address 12.23.4.5 mask 255.255.255.0
D.) ip address 12.23.4.5 mask ff:ff:ff:0
E.) that is an invalid mask for a class 'A' address | | 2 |
| Which OSI layer end to end communication, segmentation and
re-assembly?
A.) Network
B.) Transport
C.) Physical
D.) Application
E.) Data-Link
F.) Presentation | | 1 |
| What is the IEEE specification for Spanning Tree Protocol?
A.) 802.9
B.) 803.ud
C.) 803
D.) 802.1d | | 1 |
| |
| For more CCNA Interview Questions Click Here |