| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| When would you use ISDN?
A.) To connect LANs using POTS
B.) To support applications requiring voice, data, and video
C.) When you need a consistent and very high rate of data speed
D.) To connect to IBM mainframes | | 1 |
| hi... i am usin packet tracer 5.0.. i hav connect two
routers A and B. A has 200.100.25.100 and 1.0.0.1 and router
B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1
and 1.0.0.2... now i want to route 200.100.25.100 and
200.10.50.100 usin rip.. i enable rip in both the routers...
but whn i give the command show ip route... i jus get this
Codes: C - connected, S - static, I - IGRP, R - RIP, M -
mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA
- OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF
NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF
external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 -
IS-IS level-2, ia - IS-IS inter area * - candidate default,
U - per-user static route, o - ODR P - periodic downloaded
static route Gateway of last resort is not set A# so can
sombody tell me where i hav gone wrong...
thanku | | 4 |
| as we know that isdn bri port come with either a u
interface or some thing s/t interface what is the
diffrenmce between them | HCL | 1 |
| What command will not display the status of to1?
A.) show int to1
B.) show to1
C.) show interface to1
D.) show interface | | 1 |
| Which ISDN protocol prefix specifies switching and signaling?
A.) I
B.) E
C.) Q
D.) S | | 1 |
| Write an access list line which will deny
node 20.0.2.1 to anywhere on your network using
DNS via UDP. Don't worry about the other access
list lines.
| | 2 |
| Which two types of route table entries are used by a Layer 3
router to determine the appropriate path to destination?
(Choose two)
A. static route entry
B. default route entry
C. Dynamic route entry
D. temporary route entry
E. permanent route entry | | 1 |
| Identify the hardware component that stores the backup
configuration?
A.) RAM
B.) NVRAM
C.) Flash
D.) ROM | | 1 |
| Identify the type of routing protocol that maintains a
topological
database of the network?
A.) Topological state
B.) Shortest Path First
C.) Link state
D.) Distance vector | | 1 |
| Request any body to explain the parameters of Ipsec vpn
tunnel while creating a tunnel in Cisco ASA. | HCL | 3 |
| What is the purpose of the DLCI?
A.) Identifies the remote routers
B.) Contained with a 802.2 frame for routing purposes
C.) Used with PPP during authentication
D.) Identifies the PVC in a Frame Relay network | | 1 |
| What is the default bandwidth of a serial connection?
A.) 1200 baud
B.) 1.544 Mbps (T1)
C.) 10 Mbps
D.) 96Kpbs | | 3 |
| Which of the follwing are true of standard half-duplex
Ethernet circuitry?
A. It is alternate one-way communication
B. The receive (RX) is wired directly to the transmit (TX)
of the remote station
C. The transmit (TX) is wired directly to the receive (RX)
of the remote station
D. Collisions are not possible
E. Both stations can transmit simultaneously | | 1 |
| hi friend i hav difficulty n need to solve it...v need to
implement a new raw switch in company as to increase the no
of staff...snc raw switch by default is in server mode,i
wanna know 1.how to make a switch in client mode...2.how to
configure switch i mean to sy how to connect all switches to
network. | | 1 |
| Given the Novell IPX address 1aceb0b.0000.0c12.3456 which
part is
the network portion of the address?
A.) 0000
B.) 1
C.) 3456
D.) 1ace
E.) 0000.0c12.3456
F.) 1aceb0b | | 2 |
| Identify the components in the following command 'interface
serial0/1/1'
A.) Serial interface, port number 0, slot 1, port adapter 1
B.) Serial interface, slot 1, port number 1, port adapter 0
C.) Serial interface, slot 0, port adapter 1, port number 1 | | 1 |
| Which addresses are INCORRECTLY paired with their class?
A. 128 to 191, Class B
B. 192 to 223 Class B
C. 128 to 191, Class C
D. 192 to 223, Class C | | 2 |
| what are two security appliances that can be installed a
network | | 7 |
| What field tells the Internet layer how to handle an IP packet?
A. Type of Service
B. Identification
C. Flags
D. Frag Offset | | 1 |
| Identify 3 characteristics of switches?
A.) Increase available bandwidth
B.) Decrease broadcast traffic
C.) Support full duplex in a multipoint topology
D.) Make fowarding decision using MAC address
E.) Create collision domains | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
