| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What command will not display the status of to1?
A.) show int to1
B.) show to1
C.) show interface to1
D.) show interface | | 1 |
| in the ospf area network dr and bdr selection procedure occur
let there are 4 router in that n/w r1 have the higher priority
then r2 and r2 have higher priority then r3 and so on
like that
r1>r2>r3>r4
now as we know that selection of dr and bdr based upon the
router priority so in this case r1 will be dr and r2 will be
bdr
now my question is that if i am going to implement 5th
router which have greater priority then r1 then will it become dr atomically
remember that i am not going change my 5 or 1st router property
answer that one please | | 2 |
| Given the configuration example<HR>
<B>interface ethernet0
ipx network 4a
ipx access group 800 out
interface ethernet1
ipx network 3d
interface ethernet2
ipx network 5c
access list 800 permit 3d 4a</B><HR>
Which two actions result from implementing this
configuration? (Choose two)
A. IPX network 5c will not receive any traffic
B. Traffic from network 3d for network 4a will be forwarded
out e0
C. Traffic from network 4a for network 3d will be forwarded
out e0
D. Traffic from network 3d destined for network 4a will be
forwarded out e2
E. The access list is applied to an outgoing interface and
filters outbound traffic | | 1 |
| what is farme realy.and on which layer it work | | 1 |
| What information can you get from CDP info: (choose all that
apply)
A.) Hardware platform
B.) One address per protocol
C.) Software platform
D.) Hostname
E.) The same info as show version
F.) Incoming/outgoing port | | 1 |
| Identify the command that specifies Serial 0 in slot 1?
A.) Router(config)# interface serial1/1
B.) Router(config)# interface serial1/0
C.) Router(config)# interface serial0.1
D.) Router(config)# interface serial0/1 | | 1 |
| Hi Guys
I am facing one problem while configuring PAP over Point to
Point links. Configuration scenario is like this.
ROUTER 1: (Hostname – R1)
R1(config)#username R2 password CCNA2
R1(config)#interface serial 1/1
R1(config-if)ip address 10.0.0.1 255.0.0.0
R1(config-if)#lock rate 64000
R1(config-if)#encapsulation ppp
R1(config-if)#ppp authentication pap
R1(config-if)#ppp pap sent –username R1 password CCNA1
R1(config-if)#no shutdown
ROUTER 2: (Hostname – R2)
R2(config)#usename R1 password CCNA1
R2(config)#interface serial 1/1
R2(config-if)#ip address 10.0.0.2 255.0.0.0
R2(config-if)#encapsulation ppp
R2(config-if)# ppp authentication pap
R2(config-if)# ppp pap sent –username R2 password CCNA2
R2(config-if)#no shutdown
Now problem is that, after configure the command “ppp
authentication pap” the “Line protocol” status goes down on
each router. But when I disable this command using “no ppp
authentication pap”, the “Line Protocol” status goes up.
What could be the problem, can anyone explain it plzzz….!!!
Thanks in Advance…!!
Shahin..
| | 6 |
| Describe End to End network services: (Choose all that apply)
A.) Best Route selection
B.) Accomplished Segment by Segment, each segment is autonomous
C.) Flow Control & Data Integrity
D.) Best efforts packet delivery | | 1 |
| What do you use the Aux port for?
A.) Console
B.) Terminal editing
C.) Modem
D.) Backup logging | | 1 |
| In the command "router igrp 109" what does 109 signify?
A. an autonomous system
B. any network number which the router is attached to
C. the allowable length of the routing table
D. the network socket number | | 1 |
| What is the IEEE specification for Spanning Tree Protocol?
A.) 802.9
B.) 803.ud
C.) 803
D.) 802.1d | | 1 |
| You have a Class B network address divided into 30 subnets. You
will add 25 new subnets within the next year. You need 600
host IDs for
each subnet.
Which subnet mask should you use?
A.) 255.254.0.0
B.) 255.192.0.0
C.) 255.255.252.0
D.) 255.255.248 0 | | 1 |
| hi... i am usin packet tracer 5.0.. i hav connect two
routers A and B. A has 200.100.25.100 and 1.0.0.1 and router
B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1
and 1.0.0.2... now i want to route 200.100.25.100 and
200.10.50.100 usin rip.. i enable rip in both the routers...
but whn i give the command show ip route... i jus get this
Codes: C - connected, S - static, I - IGRP, R - RIP, M -
mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA
- OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF
NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF
external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 -
IS-IS level-2, ia - IS-IS inter area * - candidate default,
U - per-user static route, o - ODR P - periodic downloaded
static route Gateway of last resort is not set A# so can
sombody tell me where i hav gone wrong...
thanku | | 4 |
| If a router uses static routing, how does it learn the
route to remote networks?
The router uses a RIP request to obtain remote network
numbers.
The router uses a routing protocol to exchange remote
network numbers.
The router uses DNS request packets to obtain remote
network numbers.
The Network Administrator manually configures the remote
networks.
| | 1 |
| 3. What does a bridge use to segment a network?
A. IP Addresses
B. Broadcasts
C. Application data
D. Media Access Control addresses
| | 2 |
| Identify 2 functions of IPX access-lists?
A.) Control SAP traffic
B.) Limit number of Novell servers on a network
C.) Limit number of workstations on a network
D.) Block IPX traffic | | 1 |
| What is the IP extended access list range?
A.) 1000-1099
B.) 100-199
C.) 1-99
D.) 101-200 | | 3 |
| what are the port numbers for DNS,FTP,TELNET,SMTP,NNTP | Airtel | 2 |
| If you have configured IPX on a Serial interface, which
command would
display the IPX network and node address on the Serial 1
interface?
A.) show interface
B.) show ipx s1
C.) show interface s1
D.) show ipx int serial 1
E.) show ipx int brief | | 1 |
| 1 whatis te1,te2 and nt1 what is threre functions
2 what are the isdn protocols
3 whait is spid | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
