| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which of the following are examples of the Session Layer?
A.) IP
B.) Netbios Names
C.) NFS
D.) Token Ring
E.) SQL
F.) RPC | | 2 |
| Identify the 2 commands the saves the running-config to NVRAM?
A.) write memory
B.) copy running-config startup-config
C.) write network
D.) write backup | | 2 |
| Hi Jitendera, I need ur suggestion. I completed my CCNA
certification & also hving some sort of real time
experience. Now i m planning to do CCNP. Little bit
confusion is that whether it wud be better for me to go for
CCNP ya CCNA (Security). As off my goal is to reach CCIE
(Security & Switching/Routing). So tell me some solution of
my confusion yaar..!!!
Thanx & Regards
Shahin.. | | 1 |
| Station A is transmitting data to station B, and expects an
acknowledgment
after every 400 bytes. After transmitting data for a while,
the two
stations determine the line is reliable and change to
expecting and
acknowledgement every 600 bytes.
This is an example of (pick the best answer only):
A.) BECN
B.) Sliding Windows
C.) Poison Reverse
D.) Countdown timers
E.) Split Horizon
F.) Count to infinity | | 1 |
| Identify the true statements about the following access list:
Access-list 101 deny tcp 192.10.172.0 0.0.0.255 any eq 23
Access-list 101 permit ip any any
A.) This access list prevents the host 192.10.172.0 from
telneting
B.) This access list prevents any telnet traffic from subnet
192.10.172.0/24
C.) This access list filters some telnet access
D.) This access list denies any telnet traffic to subnet
192.10.172.0/24
E.) This access list is invalid
F.) The netmask on the this access list is reversed | | 1 |
| hi shain/sudeep and rest of all plz answer these question
for help some one as soon as possible
what is stub area
what is transit area
let there are three area in ospf a0 a2 and a3 if a2 and a3
is coneted
through each other will they comnicate | | 3 |
| Which statement about the data link connection identifier
(DLCI) is true?
A. It is a number that identifies a local virtual circuit in
a Frame Relay network
B. It is a signaling standard between the CIDE device and
the Frame Relay switch
C. It is the clock speed (pod speed) of the connection
(local loop) to the Frame Relay Cloud
D. It is the Maximum number of uncommitted bits that the
Frame Relay switch will attempt to transfer beyond the
Committed Information Rate (CIP) | | 2 |
| Which of the following protocols are used to get an IP
address from a
known MAC address?
A.) BootP
B.) TCP
C.) IP
D.) ARP
E.) RARP
F.) ICMP | | 2 |
| Which layer is responsible for providing mechanisms for
multiplexing
upper-layer application, session establishment, and tear
down of virtual
circuits?
A.) Session
B.) Network
C.) Physical
D.) Transport
E.) Application
F.) Presentation | | 1 |
| Identify 2 features of X.25?
A.) Supports only IP
B.) Utilizes switched and permanent virtual circuits
C.) Contains minimal flow control and error recovery
D.) Utilizes LAPB as it's data-link protocol | | 1 |
| Write out a config to permit only the below MAC address
to pass traffic through a port on your switch.
mac-address 0005.1b00.5b58 | | 4 |
| IPX routing updates occur how often?
A.) Every 30 seconds
B.) Every 60 seconds
C.) Only as needed
D.) When the remote router asks for an update | | 1 |
| Identify the OSI layer responsible for end-to-end connections?
A.) Network
B.) Transport
C.) Session
D.) Data link
E.) TCP | | 1 |
| What is the default CDP broadcast update rate for Cisco routers?
A.) 120 seconds
B.) 60 seconds
C.) 30 seconds
D.) 90 seconds | | 1 |
| IGRP uses flash updates, poison reverse updates, holddown
times, and split horizon. How often does it broadcast its
routing table updates?
A. 90 seconds
B. 10 seconds
C. 30 seconds
D. 45 seconds | | 1 |
| The ICMP (referred to in RFC 1700) is implented by all
TCP/IP hosts.
A. true
B. false | | 1 |
| Which protocol carries messages such as destination
Unreachable, Time Exceeded, Parameter Problem, Source
Quench, Redirect, Echo, Echo Reply, Timestamp, Information
Request, Information Reply, Address Request, and Address
Reply?
A. ICMP
B. UDP
C. TCP
D. TFTP
E. FTP | | 2 |
| Identify the 2 methods to modify the routers boot sequence?
A.) Setup program
B.) Boot system commands
C.) RXBoot
D.) Config-register | | 1 |
| Identify the command to display the IP host table?
A.) show ip hostnames
B.) show ip names
C.) show hosts
D.) show ip hosts | | 1 |
| Which command line option will determine what traffic is
interesting enough to establish a dialup connection?
A.) dialer map
B.) dialer string
C.) dialer in-band
D.) dialer-list
E.) dialer negotiation | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Ask Questions on ANYTHING, that arise in your Daily Life at 
Site Map
