When determining whether or not to route a LAN segment, which rule of t

Advertise your Business Here

Refer this Site

Login | Sign Up


	Ask Questions on ANYTHING, that arise in your Daily Life at FORUM9.COM

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

When determining whether or not to route a LAN segment,
which rule of

thumb do you use?

A.) 60/40

B.) 50/50

C.) 80/20

D.) 90/10

E.) 70/30

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: When determining whether or not to route a LAN segment, which rule of thumb do you use? A.) 60/40 B.) 50/50 C.) 80/20 D.) 90/10 E.) 70/30

Answer
# 1

Answer: E

Is This Answer Correct ?

2 Yes

0 No

Guest

Question	Asked @	Answers
Other CCNA Interview Questions


What is the default LMI type for Cisco Routers that are using Frame-Relay? A.) Gandalf5 B.) Q933A C.) Cisco D.) IETF E.) ARPA F.) SAP		2
Write an access list line which will deny node 20.0.2.1 to anywhere on your network using DNS via UDP. Don't worry about the other access list lines.		2
Cisco routers use wildcard masking to identify how to check or ignore corresponding IP address bits. What does setting a wildcard mask bit to 0 cause the router to do? A. It tells the router to check the corresponding bit value. B. It tells the router to ignore the corresponding bit value. C. It tells the router to check its alternate routing list. D. It tells the router to use its primary routing list.		1
Which command assigns the login password CISCO on the console terminal line? A. line vty 0 login password cisco B. line console login password cisco C. line login terminal password cisco D. line console 0 login E. line console 0 login password cisco		2
Which protocol resolves an IP address to a MAC address? A.) DHCP B.) RARP C.) ARP D.) NBP E.) DNS		4
what is 5-4-3 rule?		1
hi i have some difficulty plz reply as s0on as possible. 1 what is csma/cd(i know u are familer with that protocol) 2 what is the need for it and and 3 rd one in which i need help how to enable csma/cd at router or switches shain make it answer as sson as possibele and call me afetr reply thanks jitendera kuamr sinha		1
Most routing protocols recognize that it is never useful to send information about a route back out the direction from which the original packet came. This is an example of which routing technology? A.) Split Horizon B.) LMI C.) Triggered Updates D.) Poison Reverse E.) SYN, ACK F.) DLCI		1
Which statement is true regarding half duplex? A.) Only works in a point-to-point configuration B.) Allows for transmitting and receiving but not a the same time C.) Allow for transmitting and receiving of data simultaneously D.) Doubles the bandwidth		1
Identify 1 characteristic of RARP? A.) MAC to IP address translation B.) Connectionless delivery of packets C.) Can be used to initiate remote O/S load sequence D.) Generates error and control messages		3
Which type of switching is considered to be 'wire speed?' A.) Cut-Through B.) Multiplexed C.) Inverted D.) Layer 4 E.) Store and Forward F.) Layer 3		1
Which layer is responsible for flow control, acknowledgement, and windowing? A.) Transport B.) Network C.) Application D.) Session E.) Physical F.) Data Link		2
Identify the correct IGRP configuration? A.) Router# router igrp 100 Router# network 10.0.0.0 B.) Router(config)#router igrp 100 Router(config-router)#network 10.0.0.0 C.) Router(config)# router igrp Router(config-router)# network 10.0.0.0		2
Which statement about the flow control function of TCP is true? A. TCP makes no snarl to check for lost or duplicate data packets B. The application layer must sequence data packets when using TCP C. TCP controls the flow of UDP data through negative acknowledgements (NAK) D. TCP is a connection-oriented protocol that acknowledges receipt of data packets and is considered reliable		1
Which layer is responsible for coordinating communication between systems? A.) Application B.) Network C.) Session D.) Transport E.) Physical F.) Data Link	HCL	2
Identify 2 HDLC characteristics? A.) Default serial encapsulation B.) Open standard C.) Supports Stacker compression D.) Supports point-to-point and multipoint		1
Repeaters work at which layer of the OSI model? A.) Network B.) Session C.) Transport D.) Physical	Wipro	3
CSMA/CD stand for which of the following? A.) Carrier Sense, Multiple Access with Collision Detection B.) Collision Sense, Multiple Access with Collision Detection C.) Collision Sense, Multiple Access with Carrier Detection D.) Carrier Sense, MAC address with Collision Detection		1
What does a metric of 16 hops represent when using RIP? A.) Number of hops to the destination B.) Destination unreachable C.) Number of routers D.) Bandwidth		3
What are the job opportunities i will get once i complete my CCNA certification.		2

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com