| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Which of the following will apply IPX sap access list 1010 for
incoming traffic, assume you are at the interface configuration?
A.) ipx input-sap-filter 1010 in
B.) ipx input-sap-filter 1010
C.) ipx access-group 1010 in
D.) ipx access-list 1010 in | | 1 |
| b Which protocol for PPP LCP (Link Control Protocol) performs a
challenge handshake?
A. CHAP
B. PAP
C. UDP
D. IPX | | 1 |
| Identify 3 characteristics of switches?
A.) Increase available bandwidth
B.) Decrease broadcast traffic
C.) Support full duplex in a multipoint topology
D.) Make fowarding decision using MAC address
E.) Create collision domains | | 1 |
| Identify the command to display all the valid commands at the
given mode?
A.) Help all
B.) Help
C.) All commands
D.) ? | | 3 |
| Identify 3 characteristics regarding IP access-lists?
A.) Can be configured as a standard access-list
B.) Can be run from another router running IP
C.) Can be configured as a named access-list
D.) Are the same as IPX access-lists
E.) Can be configured as an extended access-list | | 1 |
| CSMA/CD stand for which of the following?
A.) Carrier Sense, Multiple Access with Collision Detection
B.) Collision Sense, Multiple Access with Collision Detection
C.) Collision Sense, Multiple Access with Carrier Detection
D.) Carrier Sense, MAC address with Collision Detection | | 1 |
| What is the connection oriented protocol in the TCP/IP
protocol stack?
A. IP
B. UDP
C. TCP
D. DNS
E. OSPF | HCL | 5 |
| Novell NetWare has an Ethernet frame type called Ethernet_802.2.
What is the matching Cisco command line keyword for this
encapsulation
method?
A.) gns
B.) arpa
C.) snap
D.) sap
E.) novell-ether
F.) dix | | 1 |
| What does a metric of 16 hops represent when using RIP?
A.) Number of hops to the destination
B.) Destination unreachable
C.) Number of routers
D.) Bandwidth | | 3 |
| Eight stations connected to separate 10 Mobs pods on a Layer
2 switch will give each station how many Mobs of bandwidth?
A. 1.25
B. 4
C. 16
D. 10
E. 80 | | 1 |
| The Datalink layer works with which of the following:
A.) Packets
B.) Bits
C.) Globules
D.) Frames
E.) Segments | | 1 |
| what is unike ip address | | 1 |
| Which statement about an IP network is true?
A. A broadcast source MAC address contains all zeros
B. A MAC address is part of the physical layer of the OSI model
C. MAC addresses are used by bridges to make forwarding
decisions. IP address are used by routers.
D. IP addresses allow a flat addressing scheme. MAC
addresses use a hierarchical addressing scheme. | | 2 |
| Which is true regarding half duplex Ethernet operation?
A.) Half Duplex ethernet technology provides a transmit
circuit connection
wired directly to the receiver circuit at the other end
B.) Half duplex transmission between stations is achieved by
using point
to multipoint Ethernet and Fast Ethernet
C.) With Half Duplex transmission logically circuits feed
into a single
cable creating a situation similar to a one way bridge
D.) Half Duplex transmission between stations is achieved
using Point to
Point Ethernet & Fast Ethernet | | 1 |
| Given an IP host address of 172.16.2.160 and a shored mask
of 255.255.255.192 to which shored does the host belong?
A. 172.16.2.32
B. 172.16.2.64
C. 172.16.2.96
D. 172.16.2.128
E. 172.16.2.192 | | 2 |
| Regarding frame relay, which of the following statements are
true?
A.) You must use ANSI encapsulation if connecting to
non-Cisco equipment
B.) You must use IETF encapsulation if connecting to
non-Cisco equipment
C.) You must use Q.933a encapsulation if connecting to
non-Cisco equipment
D.) You must use Cisco encapsulation if connecting to
non-Cisco equipment | | 2 |
| Which frame has a Type field to identify the upper-layer
protocol?
A.) 802.3
B.) 802.2
C.) 802.5
D.) Ethernet_II | | 1 |
| Which command verifies encapsulation as well as Layer 1 and
Layer 2 statistics on a router configured for Frame Relay?
A. show ip
B. show interface
C. show statistics
D. show frame-relay | | 1 |
| Hi-
Salmaan my name is Shadab Khan and nick Khangkp
ok salmaam plz tell me about of NAT plz | | 3 |
| As system administrator, you type "debug ipx sap" and
receive the following lines as part of the IOS response:
type 0x4, "HELLO2", 199.0002.0003.0006 (451), 2 hops
type 0x4, "HELLO1", 199.0002.0003.0008 (451), 2 hops
What does "0x4" signify?
A. That is a Get Nearest Server response.
B. That it is a General query.
C. That it is a General response.
D. That it is a Get Nearest Server request. | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff 
Site Map
