| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What key do you use to view the last command?
A.) Left Arrow
B.) Ctrl-P
C.) Up Arrow
D.) Right Arrow | | 2 |
| What is a characteristic of Store and Forward switches?
A.) They forward the frame before it is completely read.
B.) They work at wire speed.
C.) They are the same a Cut-Through switching.
D.) They read the entire frame and check CRC before forwarding.
E.) They decrease latency. | | 1 |
| CO is an acronym for which of the following?
A.) Central Office
B.) Capital Office
C.) Central Operator
D.) Company Office | | 1 |
| What are the 2 functions of the Data Link Mac layer?
A.) Handles access to shared media
B.) Manages protocol access to the physical network medium
C.) Provides SAPs for higher level protocols
D.) Allows multiple devices to uniquely identify one another
on the data
link layer | | 1 |
| Which command will display Ethernet 0's IP address?
A.) display ip address e0
B.) show ip interface e0
C.) show address e0
D.) sh ip address e0
E.) show all | | 1 |
| IGRP uses flash updates, poison reverse updates, holddown
times, and split horizon. How often does it broadcast its
routing table updates?
A. 90 seconds
B. 10 seconds
C. 30 seconds
D. 45 seconds | | 1 |
| Identify 3 characteristics of IP RIP?
A.) Distance vector
B.) Administrative distance is 120
C.) Periodic updates every 60 seconds
D.) Uses a composite metric
E.) Can load balance | | 1 |
| Which layer is responsible for identifying and establishing the
availability of the intended communication partner?
A.) Application
B.) Presentation
C.) Transport
D.) Session
E.) Network | | 1 |
| What is the regional Telco office called, where the customers
local loop
terminates?
A.) Demarc
B.) DTE
C.) DCE
D.) CO
E.) CPE | | 1 |
| Given the command 'cl?', what will it display?
A.) Syntax of the 'clock' command
B.) Syntax of the 'clear' command
C.) All commands that begin with 'cl'
D.) All commands that begin with 'c' | | 2 |
| Which layer is responsible for flow control,
acknowledgement, and
windowing?
A.) Transport
B.) Network
C.) Application
D.) Session
E.) Physical
F.) Data Link | | 2 |
| Which Standard IP Access list commands will deny only the source
address 1.1.1.1?
A.) access-list 9 deny host 1.1.1.1
B.) access-list 9 deny 1.1.1.1 255.255.255.0
C.) access-list 9 deny 1.1.1.1 0.0.0.0
D.) access-list 9 deny 1.1.1.1 0.255.255.255
E.) access-list 9 deny 1.1.1.1 255.255.255.255 | | 2 |
| Ping uses which Internet layer protocol?
A.) RARP
B.) ICMP
C.) ARP
D.) FTP | | 2 |
| Which statement is true regarding full duplex?
A.) Allows for transmission and receiving of data simultaneously
B.) Only works in a multipoint configuration
C.) Does not affect the bandwidth
D.) Allows for transmission and receiving of data but not a
the same time | | 2 |
| Identify the command to reload the router?
A.) Router(config)# reload
B.) Router# reset
C.) Router# reload
D.) Router> reload | | 1 |
| What is difference between IPv4 & IPv6?? | Hathway | 3 |
| Identify 3 characteristics of ISDN?
A.) Transports voice and data
B.) Transports voice only
C.) Support both BRI and PRI
D.) Runs over existing phone lines
E.) Same as X.25 | | 1 |
| Identify the keystroke used to terminate the setup mode?
A.) Ctrl-K
B.) Crtl-C
C.) Ctrl-Z
D.) Crtl-End | | 1 |
| The "ipx delay number" command will allow an administrator to
change the default settings. What are the default settings?
A. For LAN interfaces, one tick; for WAN interfaces, six
ticks
B. For LAN interfaces, six ticks; for WAN interfaces, one
tick
C. For LAN interfaces, zero ticks; for WAN interfaces, five
ticks
D. For LAN interfaces, five ticks; for WAN interfaces, zero
Ticks | | 1 |
| Which NetWare protocol provides link-state routing?
A. NLSP
B. RIP
C. SAP
D. NCP | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
