| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What does the IPX maximum path command do?
A.) Allows you to disable the TTL on an IPX packet
B.) This parameter is only used in NLSP routing
C.) Sets the maximum metric that can appear in the routing table
D.) Configures round robin load sharing over multiple equal
metric paths
(parallel paths) | | 1 |
| Which IP Address Class can have 64,000 subnets with 64,000
hosts per subnet?
A. Class B
B. Class A
C. Class C
D. Class D | | 2 |
| An optional parameter on an IPX access is the 'LOG' parameter.
This records access-list violations when a packet matches.
What else
does the 'LOG' option do?
A.) Records the number of times that a packet matches the list.
B.) Return a message to user who is denied access the by list.
C.) Notifies an SNMP Agent.
D.) Saves the log to NVRAM.
E.) Send an SNMP Trap. | | 1 |
| What is the default IPX Ethernet encapsulation?
A.) SNAP
B.) Arpa
C.) 802.2
D.) Novell-Ether
E.) SAP | | 2 |
| Which Standard IP Access list commands will deny only the source
address 1.1.1.1?
A.) access-list 9 deny host 1.1.1.1
B.) access-list 9 deny 1.1.1.1 255.255.255.0
C.) access-list 9 deny 1.1.1.1 0.0.0.0
D.) access-list 9 deny 1.1.1.1 0.255.255.255
E.) access-list 9 deny 1.1.1.1 255.255.255.255 | | 2 |
| What is Spanning Tree Protocol and how it work? I know it
is - STP is Spanning tree Protocol. It Stops the looping in
the network? How STP work? How it stop Looping in network? | | 2 |
| Which command displays the intenances using a given access list?
A. show filters
B. show ip interface
C. show active lists
D. show interface paramaters
E. configure ip access lists
F. show access-list interfaces | | 1 |
| Which command sets IGRP as the routing protocol for
autonomous system 100?
A. Router(config)#igrp 100
B. Router(config)#network 100
C. Router(config)#router igrp 100
D. Router(config)#enable igrp 100 | | 1 |
| What does the term "attenuation" mean in data communication?
1 loss of signal strength as distance increases
2 time for a signal to reach its destination
3 leakage of signals from one cable pair to another
4 strengthening of a signal by a networking device
| | 1 |
| Identify the following components of the IPX address
2e.0000.0065.ed43
A.) Not a valid IPX address
B.) Network = 2e, Subnet = 0000, Node = 0065.ed43
C.) Network = 2e.0000, Node = 0065.ed43
D.) Network = 2e, Node = 0000.0065.ed43 | | 1 |
| Identify the command to display the IP routing table?
A.) show route
B.) show ip route
C.) show ip table route
D.) show ipx route | | 1 |
| When using access lists, what does a Cisco router check first?
A. To see if the packet is routable or bridgeable
B. The destination address
C. The source address
D. The packet contents | | 1 |
| what is the difference between hdlc and ppp protocol | ASD-Lab | 4 |
| Which of the following are Session Layer standards?
A.) ASCII and EBCDIC
B.) MPEG and MIDI
C.) RPC and SQL
D.) JPEG and PICT | | 1 |
| As a system administrator, you need to set up one Ethernet
interface on the Cisco router to allow for both sap and
Novell-ether encapsulations. Which set of commands will
accomplish this?
A. interface ethernet 0.1
ipx encapsulation Novell-ether
ipx network 9e
interface ethernet 0.2
ipx network 6c
B. interface ethernet 0
ipx encapsulation Novell-ether
ipx network 9e
interface ethernet 0
ipx encapsulation sap
ipx network 6c
C. interface ethernet 0.1
ipx encapsulation Novell-ether
interface ethernet 0.2
ipx encapsulation sap
D. interface ethernet 0.1
ipx encapsulation Novell-ether
ipx network 9e
interface ethernet 0.2
ipx encapsulation sap
ipx network 6c | | 1 |
| What is VLSM? how to Calculate VLSM? where it is use and
why? | | 4 |
| Which 2 commands shows the Cisco IOS filename?
A.) show IOS
B.) show ver
C.) show flash
D.) show mem
E.) show NVRAM | | 1 |
| Identify 3 characteristics of switches?
A.) Increase available bandwidth
B.) Decrease broadcast traffic
C.) Support full duplex in a multipoint topology
D.) Make forwarding decision using MAC address
E.) Create collision domains | | 1 |
| What is the function of DDR on Cisco routers?
A. DDR is dial--on-demand routing. It provides a continuous
LAN only
connection.
B. DDR is dial-on-demand routing. It provides routing for
high volume
traffic.
C. DDR is dial--on-demand routing. It provides a continuous
WAN connection.
D. DDR is dial-on-demand routing. It provides routing for
low volume and
periodic traffic. | | 2 |
| Which of the following statements are true?
A.) Store and forward switching creates variable latency
through the switch
B.) Cut through switching creates variables latency through
the switch
C.) Cut through switching works at wire speed
D.) Store and forward switching works at wire speed | | 1 |
| |
| For more CCNA Interview Questions Click Here |
To Refer this Site to Your Friends 
Site Map
