Which type of switching is considered to be 'wire speed?' A.)

Advertise your Business Here

Refer this Site

Login | Sign Up


	Did you received any Funny E-Mails from your Friends and like to share with rest of our friends? Yeah!! you can post that stuff HERE

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

Which type of switching is considered to be 'wire speed?'

A.) Cut-Through

B.) Multiplexed

C.) Inverted

D.) Layer 4

E.) Store and Forward

F.) Layer 3

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: Which type of switching is considered to be 'wire speed?' A.) Cut-Through B.) Multiplexed C.) Inverted D.) Layer 4 E.) Store and Forward F.) Layer 3

Answer
# 1

A.) Cut-Through

Is This Answer Correct ?

2 Yes

0 No

Hari Prasad

Question	Asked @	Answers
Other CCNA Interview Questions


Identify the keystroke used to terminate the setup mode? A.) Ctrl-K B.) Crtl-C C.) Ctrl-Z D.) Crtl-End		1
NetWare IPX addressing uses a network number and a node number. Which statements are true? A. The network address is administratively assigned and can be up to 16 hexadecimal digits long. B. The node address is always administratively assigned. C. The node address is usually the MAC address. D. If the MAC address is used as the node address, then IPX eliminates the use of ARP.		1
Whith the hierarchical numbering of IP addressing what determines the spoon of the address that will identify the network number? A. subnet mask B. dots between octets C. class of the first octet D. assignments of DHCP E. address resolution process		1
Identify the command to configure the router for IGRP autonomous system 100? A.) Router(config)# router igrp 100 B.) Router> router igrp 100 C.) Router# router igrp 100 D.) Router(config)# router igrp	CMS	2
Two of the protocols that can be carried in the Protocol field of an IP packet are? A. TCP B. UDP C. FTP D. TFTP		2
If configuring a Cisco router to connect to a non-Cisco router across a Frame Relay network, which encapsulation type would you select? A.) Q933a B.) ISDN C.) IETF D.) CISCO E.) ANSI		1
What is the routing algorithm used by RIP and IGRP? A.) OSPF B.) Link-state C.) Dynamic D.) Distance Vector		2
What is true when using DDR? A.) HDLC is the preferred encapsulation B.) You must use static routing C.) You should use dynamic routing D.) You should use ISDN		1
Which layer defines bit synchronization? A.) Application B.) Network C.) Transport D.) Physical E.) Session F.) Session		1
Your PC has been configured with IP Address 192.168.3.25 and a subnet mask of 255.255.255.0. Which of the following IP Addresses is a valid default gateway address for your PC? 192.168.3.0 255.255.255.0 192.168.3.2 255.255.255.0 192.168.3.25 255.255.255.0 192.168.4.1 255.255.255.255		1
Which commands would assign and enable IPX on an interface ? A.) enable netware B.) enable novell-ether C.) router#(config)ipx routing D.) You must first enable IPX globally and then assign the network number to the interface . E.) enable ipx F.) router#(config-if)ipx network 4a		1
On Cisco catalyst 5000 how would you set the second port on the controller in the first slot to full duplex? A.) Set port duplex 1/1 full B.) Set port duplex 1/2 full C.) Set port duplex 0/1 full D.) Set port duplex 0/2 full		1
Identify the 3 kinds of routes IGRP advertises? A.) Interior B.) Dynamic C.) System D.) Exterior		1
Which of the following are examples of the Transport Layer? A.) SQL B.) UDP C.) IP D.) LLC E.) ARP		1
Identify 3 characteristics regarding IP access-lists? A.) Can be configured as a standard access-list B.) Can be run from another router running IP C.) Can be configured as a named access-list D.) Are the same as IPX access-lists E.) Can be configured as an extended access-list		1
Which protocol is used for booting diskless workstations? A.) IP B.) ARP C.) RARP D.) TCP E.) SNMP		2
Which device works at the Network Layer of the OSI model? Router Switch Bridge Hub		3
What are the two types of access lists that can be configured on a Cisco router? A. Standard B. Extended C. Filtering D. Packet		1
How does the cut-through switching technique work? A.) By using broadcast address as source addresses B.) The switch waits only for the header to be received before it checks the destination address and starts forwarding the packets C.) The LAN switch copies the entire frame into its onboard buffers and then looks up the destination address in its forwarding, or switching, table and determines the outgoing interface D.) By using a Class I repeater in a collision domain		1
Which statement is true regarding full duplex? A.) Allows for transmission and receiving of data simultaneously B.) Only works in a multipoint configuration C.) Does not affect the bandwidth D.) Allows for transmission and receiving of data but not a the same time		2

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com