| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| There are 2 types of PPP authentication supported by the Cisco
IOS. What are they?
A.) PAP
B.) PREDICTOR
C.) MD5
D.) CHAP
E.) STACKER
F.) MSCHAP | | 1 |
| Identify 3 characteristics of a MAC address?
A.) Burned into the NIC
B.) 48 bits long
C.) Length is 32 bits
D.) Used to identify a host device
E.) Contains a network portion and a host portion | | 2 |
| Identify the command to configure ALL the default VTY ports?
A.) Router(config)# line vty 0 4
B.) Router# line vty 0 4
C.) Router(config)# line vty
D.) Router(config)# line vty 0 | Accel | 2 |
| Which statement about the flow control function of TCP is true?
A. TCP makes no snarl to check for lost or duplicate data
packets
B. The application layer must sequence data packets when
using TCP
C. TCP controls the flow of UDP data through negative
acknowledgements (NAK)
D. TCP is a connection-oriented protocol that acknowledges
receipt of data packets and is considered reliable | | 1 |
| What is the command to manually enter a static route?
A.) IP route network
B.) IP route
C.) IP route < destination network>
D.) IP route | | 4 |
| Which two types of route table entries are used by a Layer 3
router to determine the appropriate path to destination?
(Choose two)
A. static route entry
B. default route entry
C. Dynamic route entry
D. temporary route entry
E. permanent route entry | | 1 |
| What is the total bandwidth of all channels on a BRI circuit?
A. 56 kps
B. 64 kps
C. 112 kps
D. 128 kps
E. 144. kps | | 5 |
| Which of the following are examples of the Datalink Layer?
A.) LLC
B.) SQL
C.) TCP
D.) Token Ring
E.) IP | | 2 |
| Identify the command to configure the configuration-register?
A.) Router# config-register 0x2102
B.) Router(config)# config-register 0x2102
C.) Router(config-reg)# 0x2102
D.) Router> config-register 0x2102 | | 1 |
| What is an example of a valid MAC address?
A. 192.201.63.251
B. 19-22-01-63-25
C. 0000.1234.FEGA
D. 00.00.12.34.FE.AA | Aricent | 3 |
| Which of the following are Distance Vector protocols?
A.) IGRP
B.) RIP
C.) OSFP
D.) EIGRP | | 3 |
| HOW MPLS IS DIFFERENT FROM OSPF? WHY NOW A DAYS MPLS IS
PREFERED OVER ANY NETWORK PROTOCOL? | Aricent | 2 |
| The Network layer works with which of the following:
A.) Globules
B.) Bits
C.) Packets
D.) Segments
E.) Frames | | 2 |
| Write out a config to permit only the below MAC address
to pass traffic through a port on your switch.
mac-address 0005.1b00.5b58 | | 4 |
| what is the subnet for the host ip address 172.16.210.0/22 | IBM | 4 |
| Can anyone explain the Split Horizon rule in RIP & also
Split Horizon with Poison reverse.
Jitu.... U knw wat i expect.. hehehehehe... | | 1 |
| The Internet Protocol (IP) occurs at what layer of the seven
layer
model?
A.) Physical
B.) Presentation
C.) Network
D.) Datalink
E.) Session
F.) Transport | | 1 |
| What is the Difference between Switch and Bridge? | | 3 |
| Suppose we have 4 switches runing in VTP mode. So when i
create a VLAN in Server Switch this VLAN info reflect in all
other switch. So question is -
A) Suppose i m practicing this scenario in BOSON software,
When a create a VLAN in server switch n ADD ports of switch
to that VLAN, the same number of ports of client switch also
belongs to dat VLAN.
For example - In switch A (Server mode), i create a VLAN 7
name Hyderabad & port number 1, 2 & 3 put into this VLAN.
Another Switch B (Client mode), its also showing that port
number 1,2 & 3 belong the same VLAN.
How cud it possible... As we know, VTP share only VLAN
configuration information. Cud anyone explain it please....!!!!
B)Same thing, when i m practicing in PACKET TRACER 5.0, its
only showing that VLAN configuration information is shared.
No port information is shared at all. I can manually
configure individual switch port to respective VLAN as our wish.
Cud anyone explain it please..!!!
| | 3 |
| A big part of the overhead on a network is broadcasts. You
divide a large number of hosts into smaller individual
networks and separate them with the proper device
According to proper networking terminology you have created
separate _______________________,
User Domains
Broadcast Domains
Collision Areas
Broadcast Areas
| | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
