Which layer of the 7 layer model is responsible for representing the ap

Advertise your Business Here

Refer this Site

Login | Sign Up


	Ask Questions on ANYTHING, that arise in your Daily Life at FORUM9.COM

Categories >> Certifications >> Cisco Certifications >> CCNA

CCNA Interview Questions

CCDA Interview Questions

Question

Which layer of the 7 layer model is responsible for
representing the

application information between 2 different OS's? For
example, converting

ASCII to EBCIDIC.

A.) Transport

B.) Application

C.) Physical

D.) Session

E.) Presentation

F.) Network

Question Submitted By :: Guest

I also faced this Question!!

Rank

Answer Posted By

Re: Which layer of the 7 layer model is responsible for representing the application information between 2 different OS's? For example, converting ASCII to EBCIDIC. A.) Transport B.) Application C.) Physical D.) Session E.) Presentation F.) Network

Answer
# 1

Answer: E

Is This Answer Correct ?

0 Yes

1 No

Guest

Answer
# 2

e. presentation layer

Is This Answer Correct ?

0 Yes

0 No

Kushal Singh Bisht

Question	Asked @	Answers
Other CCNA Interview Questions


What is the default CDP broadcast update rate for Cisco routers? A.) 120 seconds B.) 60 seconds C.) 30 seconds D.) 90 seconds		1
What is true about frame-relay DLCI? A.) DLCI represents a single physical circuit B.) DLCI is optional in all frame-relay networks C.) DLCI identifies a logical connection between DTE devices D.) DLCI is used to tag the beginning of a frame with VLAN information		1
Identify IPX SAP and it's purpose? A.) Sonet Access Pipe - interface to Sonet ring B.) Service Advertising Protocol - advertise services C.) Server Appletalk Protocol - appletalk directory services D.) Service Access Point - identify upper layer protocols		1
Identify the 3 pieces of hardware you would not install to prevent broadcasts? A.) Switch B.) Repeater C.) Bridge D.) Router		1
Which IP address and wildcard mask would you use in your ACL to block all the hosts in the subnet 192.168.16.43/28?	Siemens	2
Which of the following are Distance Vector protocols? A.) IGRP B.) RIP C.) OSFP D.) EIGRP		3
Identify 2 characteristics of PPP? A.) Uses LLC to establish the link B.) Default serial encapsulation C.) Support multiple layer 3 protocols D.) Offers two types of authentication; PAP and CHAP		3
How does the cut-through switching technique work? A.) By using broadcast address as source addresses B.) The switch waits only for the header to be received before it checks the destination address and starts forwarding the packets C.) The LAN switch copies the entire frame into its onboard buffers and then looks up the destination address in its forwarding, or switching, table and determines the outgoing interface D.) By using a Class I repeater in a collision domain		3
What is the most common layer 2 device? A. Hub B. Bridge C. Switch D. Router		1
what is LAPB	ASD-Lab	1
Identify the command to display the Frame Relay map table? A.) Router# display frame-relay map B.) Router# show frame-relay map C.) Router(setup)# show frame-relay map D.) Router# show map frame-relay		1
Identify the command that configures the bandwidth to 56K? A.) Router(config-if)# bandwidth 56000 B.) Router(config-if)# bandwidth 56k C.) Router(config)# bandwidth 56 D.) Router(config-if)# bandwidth 56		1
Identify 3 ways in which a router can be configured? A.) TFTP B.) Nvram C.) Ping D.) Console E.) Trace		1
Which protocol will let neighbor routers know if your internetwork experienced congestion on a serial port? A.) BootP B.) IP C.) ICMP D.) ARP E.) FTP F.) RARP		1
What is the default size of a standard ping on a Cisco router? * A: 100 bytes * B: 32 bytes * C: 10 bytes * D: 16 bytes	CMS	2
What command will not display the status of to1? A.) show int to1 B.) show to1 C.) show interface to1 D.) show interface		1
Identify the definition of demarcation? A.) Date in which the WAN service contract expires B.) Cabling which extends from the WAN service provider to the customer C.) Division of responsibility, where the CPE ends and the local loop begins D.) Equipment which is located at the customer premises		1
Routers that have Flash memory typically have a ore loaded copy of place IOS software. Which command should you use to make a backup copy of the software image onto a given network server? A. copy flash tftp B. save copy to tftp C. write backup tftp D. write, backup -server-name- E. copy backup to -server-name-		1
What three occurrences will reset the holddown timer after a triggered update? A.) Infinity is finally defined as some max number B.) HD Timer expires C.) Another update is received indicating a better metric D.) The router receives a processing task proportional to the number of links in the internetwork E.) The router detects fault LSP's propagating through the internetwork F.) Another update is received indicating net status changed		1
Which of the following are used by routers to learn routes to be added to the routing table? Ping and Traceroute MAC address resolution Acknowledgments and Sequence Numbers Routing updates and static routes		1

For more CCNA Interview Questions Click Here


Copyright Policy \| Terms of Service \| Help \| Site Map 1 \| Articles \| Site Map \| Site Map \| Contact Us \|

Copyright © 2007 ALLInterview.com. All Rights Reserved.

ALLInterview.com :: Forum9.com :: KalAajKal.com