| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What is the default interval for SAP updates?
A.) 60 seconds
B.) 15 seconds
C.) 30 seconds
D.) 120 seconds | ACS | 1 |
| What are the two types of access lists that can be
configured on a
Cisco router?
A. Standard
B. Extended
C. Filtering
D. Packet | | 1 |
| Which of the following are Transport layer protocols?
A.) UDP
B.) TCP
C.) NBP
D.) IP
E.) SPX | | 1 |
| What is the regional Telco office called, where the customers
local loop
terminates?
A.) Demarc
B.) DTE
C.) DCE
D.) CO
E.) CPE | | 1 |
| What are the 3 ways routers learn paths to destination networks?
A.) Dynamic
B.) Static
C.) Routing tables
D.) Default | | 1 |
| The default routing protocol for IPX is IPX RIP. How do you view
the routing updates sent and received by the router?
A.) debug ipx routing
B.) debug ipx routing activity
C.) debug rip
D.) show ipx routing
E.) sh ipx
F.) debug ipx rip | | 2 |
| What is a key use of a device hardware address?
A. to obtain a vendor code / serial number from the user
B. to transmit a frame from one Interface to another Interface
C. to transmit a packet from one local device to another
local device
D. to transmit data from one local device to a remote device
across the internet
E. to contain logical information about the device to use
for end-to-end transmission | | 1 |
| Identify the command that disables name-to-address translation?
A.) Router(config-dns)# no ip domain-lookup
B.) Router(config)# no address translation
C.) Router(config)# no ip domain-lookup
D.) Router(config)# ip domain-lookup | | 1 |
| Given the configuration example<HR>
<B>interface ethernet0
ipx network 4a
ipx access group 800 out
interface ethernet1
ipx network 3d
interface ethernet2
ipx network 5c
access list 800 permit 3d 4a</B><HR>
Which two actions result from implementing this
configuration? (Choose two)
A. IPX network 5c will not receive any traffic
B. Traffic from network 3d for network 4a will be forwarded
out e0
C. Traffic from network 4a for network 3d will be forwarded
out e0
D. Traffic from network 3d destined for network 4a will be
forwarded out e2
E. The access list is applied to an outgoing interface and
filters outbound traffic | | 1 |
| How Bridge Protocol Data Unit detect looping in Network?
How Bridge Protocol Data Unit work? explain? | | 1 |
| What is the routing algorithm used by RIP and IGRP?
A.) OSPF
B.) Link-state
C.) Dynamic
D.) Distance Vector | Cisco | 2 |
| What’s the default CDP holdtime in seconds for Cisco routers?
| | 2 |
| Your network uses a Class C address of 210.10.10.0. You
must now split up the network into separate shores to handle
multiple buildings separated by routers. Which two steps
must you take to determine the proper shored mask for your
networks? (Choose two)
A. determine the number of seperate networks required
B. determine how many devices will require DHCP addressing
C. determine the maximum number of hosts that will be on
each shored
D. determine the miniumum number of hosts that will be on
each shored
E. determine which router will be the IP default gateway for
each shored | | 1 |
| All equipment located at the customers site is called:
A.) CPE
B.) CO
C.) DCE
D.) Demarc
E.) DTE | | 1 |
| How many Frame-relay encapsulation types are available with
Cisco
routers?
A.) Four
B.) Two
C.) Five
D.) Three | | 2 |
| mention the funtions about connection oriented and
connectionless protocol and how it works ? | | 4 |
| Identify the command to display the IP routing table?
A.) show route
B.) show ip route
C.) show ip table route
D.) show ipx route | | 1 |
| The maximum distance on a 10BaseT network from the hub to a
workstation is
which of the following?
A.) 500 meters
B.) 1000 meters
C.) 100 meters
D.) 1500 meters | | 1 |
| Can anyone explain the load balancing of PVST+???? | | 1 |
| A traffic light is an example of what type of mechanism?
A.) Collision detection
B.) Flow control
C.) Sequence numbering
D.) Network management | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
