| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| What does the 'S' mean when looking at the routing table?
A.) Statically connected
B.) Directly connected
C.) Dynamically attached
D.) Shutdown route | | 1 |
| Identify the command to configure a description on an interface?
A.) Router> description Finance department
B.) Router(config)# description Finance department
C.) Router(config-if)# description Finance department
D.) Router# description Finance department | | 1 |
| Which OSI Reference Layer is concerned with logical addressing?
A.) Network
B.) Transport
C.) Datalink
D.) Physical
E.) Session | | 1 |
| How would you set the clock rate to 64K, on interface serial 0,
from the interface configuration mode?
A.) clock rate 64000
B.) bandwidth 64
C.) clock 64
D.) rate 64
E.) clock rate 64k
F.) clock rate 64 | | 1 |
| Which layer of the 7 layer model provides services to the
Application
layer over the Session layer connection?
A.) Transport
B.) Application
C.) Session
D.) Network
E.) Datalink
F.) Presentation | | 1 |
| You have typed "ping" 172.16.101.1 and get the following
display:
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echoes to 172.16.101.1,
timeout is 2 seconds:
.!!!!
What does the "." signify?
A. That one message timed out.
B. That all messages were successful.
C. That one message was successful.
D. That one message completed in under the allotted
timeframe. | | 1 |
| Which layer of the 7 layer model is responsible for representing
the application information between 2 different OS's? For
example,
converting ASCII to EBCIDIC.
A.) Transport
B.) Application
C.) Physical
D.) Session
E.) Presentation
F.) Network | | 1 |
| Which command would you type to show SAP and RIP updates you are
receiving on an interface?
A.) sh ipx servers
B.) sh ipx traffic
C.) sh ipx interface
D.) sh ipx route | | 1 |
| Which protocol resolves an IP address to a MAC address?
A.) DHCP
B.) RARP
C.) ARP
D.) NBP
E.) DNS | | 3 |
| The two sublayers of the IEEE Data Link Layer are which of the
following?
A.) Link and Logical Control
B.) Data Link and LLC
C.) Logical Link Control and Media Access Control
D.) Data Link and MAC | | 1 |
| Identify 2 characteristics of PPP?
A.) Uses LLC to establish the link
B.) Default serial encapsulation
C.) Support multiple layer 3 protocols
D.) Offers two types of authentication; PAP and CHAP | | 1 |
| Which type of switching reads in the entire frame before
forwarding it?
A.) Pause-and -forward
B.) Store-and-Forward
C.) Inverse ARP
D.) Fast Forward
E.) Cut-Through
F.) Routing | | 1 |
| On Cisco catalyst 5000 how would you set the second port on the
controller in the first slot to full duplex?
A.) Set port duplex 1/1 full
B.) Set port duplex 1/2 full
C.) Set port duplex 0/1 full
D.) Set port duplex 0/2 full | | 1 |
| What is the default bandwidth of a serial connection?
A.) 1200 baud
B.) 1.544 Mbps (T1)
C.) 10 Mbps
D.) 96Kpbs | | 1 |
| In order to limit the quantity of numbers that a system
administrator has to enter, Cisco can use which abbreviation
to indicate
0.0.0.0?
A. host
B. any
C. all
D. include | | 1 |
| Identify 2 transport layer protocols?
A.) IP
B.) TCP
C.) CDP
D.) ARP
E.) UDP | | 1 |
| What is true about frame-relay DLCI?
A.) DLCI represents a single physical circuit
B.) DLCI is optional in all frame-relay networks
C.) DLCI identifies a logical connection between DTE devices
D.) DLCI is used to tag the beginning of a frame with VLAN
information | | 1 |
| Which encapsulation methods are most commonly used with
dialup Integrated Services Digital Network (ISDN)?
A. IP and IPX
B. IP and PPP
C. PPP and SDLC
D. PPP and HDLC | | 1 |
| What is the connection oriented protocol in the TCP/IP
protocol stack?
A. IP
B. UDP
C. TCP
D. DNS
E. OSPF | HCL | 2 |
| What parameter is used with statically assigned routers to tell
packets
which interface to use to reach a distant network?
A.) Mask
B.) Subnet
C.) Default gateway
D.) Interface | | 1 |
| |
| For more CCNA Interview Questions Click Here |
Site Map
