| Other CCNA Interview Questions |
| |
| Question | Asked @ | Answers |
| |
| Identify the command to determine if an IP access-list is
grouped
on interface e0?
A.) Router(config)# show ip interface e0
B.) Router> show ip interface e0
C.) Router# show interface e0
D.) Router# show ip interface e0 | | 1 |
| What key do you use to view the last command?
A.) Ctrl+X
B.) Ctrl+Z
C.) Ctrl+E
D.) Ctrl+P | | 1 |
| Which of the following describe full-duplex transmission?
A.) Uses a single wire
B.) Data transmission in both directions, but only one way
at a time
C.) Uses a point-to-point connection from the transmitter of the
transmitting station to the receiver of the receiving station
D.) Data transmission in only one direction | | 1 |
| To monitor ipx traffic on a network, what command would you use?
A. debug ipx transaction
B. show ipx traffic
C. show ipx events
D. display ipx traffic | | 2 |
| How many Frame-relay encapsulation types are available with
Cisco
routers?
A.) Four
B.) Two
C.) Five
D.) Three | | 1 |
| What 2 commands verify end to end communications?
A.) Trace
B.) debug ip session
C.) Ping
D.) Route | | 2 |
| Identify the X.25 addressing standard?
A.) X.121
B.) X.25a
C.) ITU-1
D.) Q933a | | 1 |
| what is standard and extended acess list?
what are the commands for extended and acess list? | HCL | 3 |
| Identify the default values that make up IGRP's composite
metric?
A.) Bandwidth
B.) Load
C.) Reliability
D.) MTU
E.) Delay | | 1 |
| What is an advantage of LAN segmentation?
A.) Increases broadcasts.
B.) Increases collisions.
C.) Provides more protocol support.
D.) Decreases broadcasts.
E.) Routing protocol support. | | 2 |
| What is the function of the Transport layer and which protocols
reside
there?
A.) MAC addressing - IP
B.) Interhost communication - SQL, NFS
C.) Best effort Packet delivery - TCP, UDP
D.) End-to-end connections - TCP, UDP | | 1 |
| Where is the point between the customers site and the phone
carrier that responsibility changes?
A.) CO
B.) Demarc
C.) DCE
D.) DTE
E.) CPE | | 1 |
| Choose three reasons why the networking industry uses a layered
model:
A.) It facilitates systematic troubleshooting
B.) It allows changes in one layer to occur without changing
other layers
C.) It allows changes to occur in all layers when changing
one protocol
D.) It clarifies how to do it rather than what general
function to be done
E.) It clarifies what general function is to be done rather
than how to
do it | | 1 |
| How ICMP is used in ping and traceroute facilities | | 3 |
| What is the standard ISDN term for a native ISDN modem?
A.) ET
B.) LE
C.) TE2
D.) TE3
E.) TA | | 1 |
| Identify 2 features of PPP PAP authentication?
A.) Username and password is sent in clear text
B.) Authentication messages are sent periodically during the
connection
C.) More secure than CHAP
D.) Remote node is control of authentication process | | 1 |
| Identify the command that displays traffic statistics on
serial0/1?
A.) display interface serial0/1
B.) show interface serial0/1
C.) show seria0/1 stats
D.) show interface serial0/1 stats | | 1 |
| Identify 3 feature of access-lists?
A.) Implicit deny will deny any packets not matched
B.) Processed sequentially from bottom to top
C.) Processed sequentially from top to bottom
D.) If a packet is denied it would be tested against the
remaining
statements in the access-list
E.) Once a match is made the packet is either denied or
permitted
F.) Enabled on all interfaces by default | | 1 |
| Identify the 2 commands that copies the configuration in
NVRAM to
RAM?
A.) copy backup-config running-config
B.) configure nvram
C.) copy startup-config running-config
D.) configure memory | | 2 |
| Which two types of route table entries are used by a Layer 3
router to determine the appropriate path to destination?
(Choose two)
A. static route entry
B. default route entry
C. Dynamic route entry
D. temporary route entry
E. permanent route entry | | 1 |
| |
| For more CCNA Interview Questions Click Here |